Gage Bilt GB751FP Installation Tool Information
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Power Tool
  5. GB751FP
  6. Installation tool information

Gage Bilt GB751FP Installation Tool Information

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
S/N: 1001 AND ABOVE
GB751FP
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading

Related Manuals for Gage Bilt GB751FP

Summary of Contents for Gage Bilt GB751FP

  • Page 1 S/N: 1001 AND ABOVE GB751FP PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    Setting stroke - .780" (19.8 mm) Rated pull load - 2,200 lbs. (9.8 kN) Noise level - 81.5 dB (A) Vibration - Tested– No Hazards Found S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    Shock: It is recommended operator wear a suitable gloves WARNING during operation where prolonged use is expected. Air pressure not to exceed 100 psi (6.9 bar). S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 4: Principle Of Operation

    CYLINDER HEAD HEAD PISTON PRESSURE PRESSURE PRESSURE PISTON PISTON PRESSURE PRESSURE VALVE SPOOL PISTON PRESSURE PRESSURE PRESSURE EXHAUST Image may not reflect actual tool S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: How To Use The Gb751Fp

    (703618), the stem will eject to the rear of the tool. WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up. Image may not reflect actual tool. S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Description And Maintenance

    2200 lbs. (9.8 kN) with 90 psi. (6.2 bar) air pressure at the air inlet. The GB751FP riveter operates on a wide range of air pressure, with 90 to 100 psi. (6.2-6.9 bar) providing the maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB751FP does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles a minute.

  • Page 7: Filling, Bleeding

    With the foot pedal assy (703618) released, check dimension (A). Pressing the foot pedal assy (703618) down check dimension (B). If stroke is not consistent within 1/64" (.0156) repeat bleeding steps 4-6. .185 (4.7mm) .965 (24.5mm) S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Troubleshooting

    Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 9: Overhaul

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in Front of tool or rear of tool when installing fastener.

  • Page 10: Disassembly And Parts Lists

    The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding instructions.) Apply Loctite® #242 and torque the button head cap screws (A-928) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129). FOOT PEDAL ASSY S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 11 NOTE: Valve spring tool (704162) will facilitate the proper installation of the spring (704141). Valve sleeve (704140) can be pulled out using valve sleeve removal tool (704163). S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations S/N: 1001 AND ABOVE 10/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 13: Nose Assembly Selection Chart

    ASP® IS A REGISTERED TRADEM ARK OF ALCOA INC. CHERRYM AX® AND M BC® ARE REGISTERED TRADEM ARKS OF CHERRY AEROSPACE. FASTACK® AND SUPERTACK® ARE REGISTERED TRADEM ARKS OF ALLFAST FASTENING SYSTEM S INC. GAGE BILT CERTIFIES THE GB751 WILL INSTALL THE ABOVE FASTENERS PLEASE NOTE: Due to lever assembly 1) RIGHT ANGLE NOSE ASSEMBLIES MAY REQUIRE MORE THAN ONE PULL.

  • Page 14: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB751FP FASTENER INSTALLATION TOOL This product specified above conforms to the above dIrectives and standards.

Table of Contents