Page 1
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. GB743SRV INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT 44766 Centre Court, Clinton Twp., MI. 48038 USA Ph: +1 (586) 226-1500 Fax: +1 (586) 226-1505 MADE in USA solutions@gagebilt.com / www.gagebilt.com...
Overhaul ....................................14-16 Parts Lists .................................... 17-18 DEXRON® III Oil Safety Data (Safety Data Sheet) ......................... 19 Nose Assembly Selection Chart / Accessories ........................ 20-24 GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct., Clinton Twp., Michigan U.S.A. +1 (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str.
The GB743SRV split handle installation tool operates on 90 to 100 psi. (6.2-6.9 bar) of air pressure, with 90 psi (6.2 bar) providing maximum efficiency. At 90 psi (6.20 bar) of air pressure, the GB743SRV does not exceed 85 dB(A) and consumes .30 SCF/cycle (8.50 L/cycle).
Bleed Screw Pintail Vacuum Tube Hydraulic Hose “Pull” Lever Assembly Actuator Air Line Bleed Screw Air Inlet Flow_Speed Control Valve Muffler Handle Assembly Vacuum Regulator GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
4. Support the weight of the tool in a stand, tensioner or balancer, because a lighter grip GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Air Piston moves down Air exhaust Air exhaust Pressurized Oil Unpressurized Oil Pressurized Air Unpressurized Air Image may not reflect actual tool GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
HEAD CYLINDER FASTENER WORK ACTUATOR RED SHIPPING PLUG AIR INLET USER QUICK DISCONNECT FITTING AIR HOSE Image may not reflect actual tool or fastener GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Exert firm pressure against fastener during installation. Press actuator to start cycle. Release actuator as soon as fastener breaks. Repeat steps 1-4. Images may not reflect actual tool or fastener GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair must be done by qualified personnel trained on Gage Bilt procedures. WARNING: Excessive contact with hydraulic oil and lubricants must be avoided.
Hole marked #4 on Manifold Power Cylinder hole Oil Passage hole Handle (744303) O’ring (S832) ***Keep air hole free from oil*** Images may not reflect actual tool. GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Subtract dim (B) from dim (A). If stroke is not consistent within 1/64" (.396 mm) repeat bleeding steps until stroke met. For your consideration, Gage Bilt offers a depth gage (Pt.# A-1935) to help simplify and more accurately check your tool stroke.
Note: The vacuum regulator may visually appear clean, but still may be actual tool contaminated with a thin film, therefore, the steps above should 4) S.H.C.S. be performed to assure best performance. Fitting GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Perform overhaul in a clean, well lit area using care not to scratch or nick any smooth surface that comes in contact with an o'ring. Use of Lubriplate® (Gage Bilt part no. 402723) or other lubricant is recommended during reassembly to prevent tearing or distorting of o'rings.
Page 15
Insert and turn 5/8” open end box wrench / adjustable wrench and snug tight approximately 1/4-1/2 turn. Re-attach the lever assembly (724017) with pin. GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Page 16
Valve spring installation tool (744251) will facilitate the proper installation of the spring (744144). Valve sleeve (743144) can be pulled out using valve sleeve removal tool (744152). GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
GB743SRV ACCESSORIES Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) *Apply Vibra-tite® part # 405125 to all threads and allow it to set 20 minutes prior to assembly.
Page 21
8N-743-24 and spare nose tip (10204) to convert to 6N-743-24. All other nose tips must be ordered separately. When ordering tool fastener specific, contact Gage Bilt for more information. “VT“ installation tools are not furnished with the nose assemblies above and must be ordered for your specific fastener.
Page 22
5t Hyd. Hoses are recommended with use of Backpack Additional custom lengths are available. Accessories Cont. Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design. (Sold Separately) Tool Stroke Depth Gage...
Page 23
This page intentionally left blank GB743SRV S/N: 1063 AND ABOVE REV. 5/22 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
Page 24
Riveter Kits Available (Sold Separately) Gage Bilt offers a wide selection of standard and custom kits tailored to your needs. Contact us for more information. Approved Split Riveter Tool Backpacks For 5ft hose Split System Tools. (Sold Separately) DEXRON® IS A REGISTERED TRADEMARK OF GENERAL MOTORS CORPORATION. LUBRIPLATE® IS A REGISTERED TRADEMARK OF FISKE BROTHERS REFINING. LOCTITE® IS A REGISTERED TRADEMARK OF HENKEL CORPORATION.
Need help?
Do you have a question about the GB743SRV and is the answer not in the manual?
Questions and answers