Gage Bilt GB722 Installation Manual
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Power Tool
  5. GB722
  6. Installation manual

Gage Bilt GB722 Installation Manual

Hide thumbs Also See for GB722:
Table of Contents

Advertisement

Quick Links

Download this manual
S/N: 1753 AND ABOVE
GB722
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB722 and is the answer not in the manual?

Questions and answers

Related Manuals for Gage Bilt GB722

Summary of Contents for Gage Bilt GB722

  • Page 1 S/N: 1753 AND ABOVE GB722 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    Setting stroke - .590" (15.0 mm) Rated pull load - 4,700 lbs. (20.91 kN) Noise level - 81.5 dB (A) Vibration - Tested– No Hazards Found. S/N: 1753 AND ABOVE REV. 1/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    73.2 dB (A). In this daily basis for damage or wear. Any repair should condition the max level was 81.5 dB (A). Therefore, be done by qualified personnel trained on Gage Bilt it is required where prolonged use, hearing procedures.

  • Page 4: Principle Of Operation

    CYLINDER HEAD HEAD PISTON PRESSURE PRESSURE PRESSURE PISTON PISTON PRESSURE PRESSURE VALVE SPOOL PISTON PRESSURE PRESSURE PRESSURE EXHAUST Image may not reflect actual tool. S/N: 1753 AND ABOVE REV. 1/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: How To Use The Gb722

    Always disconnect air supply when tool is not in use to prevent accidental start-up. NOSE HEAD ASSEMBLY CYLINDER ASSY DEFLECTOR RIVET WORK ACTUATOR SHIPPING ASSY PLUG Image may not reflect actual tool. QUICK DISCONNECT FITTING S/N: 1753 AND ABOVE REV. 1/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Description, Operation And Maintenance

    The GB722 riveter operates on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency. At 90 psi. (6.2 bar) air pressure, the GB722 does not exceed 81.5 dB (A) and consumes 3 cfm at 20 cycles a minute.

  • Page 7: Filling, Bleeding And Troubleshooting

    Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. S/N: 1753 AND ABOVE REV. 1/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Overhaul, Disassembly And Parts Lists

    Disconnect tool from its air source before performing overhaul. WARNING: Tool must be maintained in a safe working condition at all times and examined on a regular daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection.
  • Page 9 The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding instructions.) Apply Loctite® #242 and torque the four socket-head cap screws (A-928) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129). S/N: 1753 AND ABOVE REV. 1/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 10: Air Valve

    NOTE: valve spring tool (704162) will facilitate the proper installation of the spring (704141), valve sleeve (703139) can be pulled out using valve sleeve removal tool (704163). S/N: 1753 AND ABOVE REV. 1/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 11: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations S/N: 1753 AND ABOVE REV. 1/15 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Nose Assembly Selection Chart

    M ONOB OLT® IS A REGISTERED TRA DEM A RK OF A VDEL UK LIM ITED. A SP ® IS A REGISTERED TRA DEM A RK OF A LCOA INC. CHERRYM A X® A ND M B C® A RE REGISTERED TRA DEM A RKS OF CHERRY A EROSP A CE FA STENERS. GAGE BILT CERTIFIES THE GB722 WILL INSTALL THE ABOVE FASTENERS *ALL RIGHT ANGLE NOSE ASSEMBLIES REQUIRE 722142 STROKE LIMITER.

  • Page 13: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB722 FASTENER INSTALLATION TOOL This procuct specified above conforms to the above dIrectives and standards.

Table of Contents