Gage Bilt GB752 Installation Tool Information
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Power Tool
  5. GB752
  6. Installation tool information

Gage Bilt GB752 Installation Tool Information

Hide thumbs Also See for GB752:
Table of Contents

Advertisement

Quick Links

Download this manual
GB752
GAGE BILT
MADE IN U.S.A.
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
44766 Centre Court
Clinton Twp. MI 48038
e-mail: solutions@gagebilt.com / www.gagebilt.com
1
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
(586) 226-1500
(586) 226-1505 Fax
REV.11/14

Advertisement

Table of Contents
loading

Related Manuals for Gage Bilt GB752

Summary of Contents for Gage Bilt GB752

  • Page 1 E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A. S/N: 3210 AND ABOVE e-mail: solutions@gagebilt.com / www.gagebilt.com REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 2: Table Of Contents

    Setting stroke - .500" (12.7 mm) Rated pull load - 3,800 lbs. (16.9 kN) Noise level - 81.5 dB (A) Vibration - Tested– No Hazards Found S/N: 3210 AND ABOVE REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    Shock: It is recommended operator wear a suitable glove WARNING during operation where prolonged use is expected. Air pressure not to exceed 100 psi (6.9 bar). S/N: 3210 AND ABOVE REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 4: Principle Of Operation

    CYLINDER HEAD HEAD PISTON PRESSURE PRESSURE PRESSURE PISTON PISTON PRESSURE PRESSURE VALVE SPOOL PISTON PRESSURE PRESSURE PRESSURE EXHAUST Image may not reflect actual tool S/N: 3210 AND ABOVE REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: How To Use The Gb752

    (704343), the stem will eject to the rear of the tool. WARNING: Always disconnect air supply when tool is not in use to prevent accidental start-up. Image may not reflect actual tool S/N: 3210 AND ABOVE REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Description, Operation And Maintenance

    3800 lbs. (16.9 kN) with 90 psi (6.2 bar) air pressure at the air inlet. The GB752 riveter is designed to operate on a range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency.

  • Page 7: Filling, Bleeding And Troubleshooting

    Replace worn or broken parts. Clean the surface the jaws ride on. Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble. Incorrect follower. S/N: 3210 AND ABOVE REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Overhaul

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or rear of tool when installing fastener.

  • Page 9: Disassembly And Parts Lists

    The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding instructions.) Apply Loctite® #242 and torque the button head cap screws (A-928) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129). S/N: 3210 AND ABOVE REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 10 NOTE: Valve spring tool (704162) will facilitate the proper installation of the spring (704141), valve sleeve (703139) can be pulled out using valve sleeve removal tool (704163). S/N: 3210 AND ABOVE REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 11: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. S/N: 3210 AND ABOVE REV.11/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Nose Assembly Selection Chart

    TRADEM ARKS OF AVDEL UK LIM ITED. ASP®, M AGNA-LOK® AND M AGNA-BULB® ARE REGISTERED TRADEM ARKS OF ALCOA INC. BULB-TITE® IS A REGISTERED TRADEM ARK OF GESIPA FASTENERS USA, INC. ULTRA-GRIP® IS A REGISTERED TRADEM ARK OF EM HART TEKNOLOGIES. GAGE BILT CERTIFIES THE GB752 WILL INSTALL THE ABOVE FASTENERS PLEASE NOTE: Due to *ALL RIGHT ANGLE NOSES REQUIRE 752142 STROKE LIMITER.

  • Page 13: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB752 FASTENER INSTALLATION TOOL This product specified above conforms to the above dIrectives and standards.

Table of Contents