Advertisement
P
= 729 bar
n
OK
P = 0 bar
7.6) Errors/Malfunctions
P = 0 bar
These appear on the display during operation, combined with a beep to notify the operator of
procedural or operational errors.
P
= 325 bar
p
Message
P
= 325 bar
p
P
= 729 bar
n
P =
0 bar
P
= 729 bar
n
P =
0 bar
ERROR
P
= 729 bar
n
P
= 731 bar
P
p
= 729 bar
n
P
= 731 bar
p
P
= 729 bar
ERROR
001
n
OK
P
= 729 bar
n
OK
002
OK
001
OK
003
SAVE 60%
SAVE 60%
002
004
003
100
004
100
LED
min.
ON
LED
ON
BATTERY
NTC
ERROR
LED
FAULT
NTC
ERROR
min.
OFF
ERROR
FAULT
ERROR
BATTERY
LED
ON
001
LED
001
OFF
001
001
002
002
LED
002
ON
002
003
003
003
003
004
004
004
004
25
min.
Error description
In CUTTING mode:
The cutting phase has been inten-
tionally interrupted by the operator.
The pump has not developped the
pressure needed to cut the cable
and the signal from the blade travel
sensor is missing.
LED
In CRIMPING mode:
ON
LED
Oil discharge is activated before wait-
ON
ing for the motor to be automatically
LED
switched
off.
OFF
LED
The pump reached the maximum
OFF
pressure but the signal from the blade
travel sensor is missing.
This error happens when:
- the cutting head is out of range.
- the cutting head used is not paired
to the pump.
- the head has not been able to cut
the cable.
LED
OFF
LED
The pump has been started without
OFF
the flexible hose connected or the
hose is not correctly connected.
Interruption of the signal from the
NTC temperature probe of the battery.
Abnormal power consumption of
the motor.
The pump stops.
Output voltage of the pressure trans-
mitter is out of the pre-set range.
The pump stops and doesn't re-start.
Failure to reach the set pressure within
120 seconds of continuous operation
of the pump.
Overcharging of the battery with
protection tripping.
The pump stops.
RESET
SW:S1J41405
RESET
SW:S1J41405
90°
90°
max 90°
max 90°
In order to reset the alarm, press the pump
button on the radio control once for 2 seconds.
max.
min.
Repeat the cycle by holding the pump button
max.
min.
until the signal from the blade travel sensor is
received (steady buzzer and steady LED light).
BATTERY
BATTERY
BATTERY
BATTERY
Repeat the crimping cycle, keeping the pump
button pressed down until the motor switches
off automatically.
BEEP
In order to reset the alarm, press the pump
BEEP
button once for 2 seconds, repeat the cut.
Before approaching the cutting area to
check the problem, strictly follow the safety
and working procedures established by the
responsible power utility.
- position the head next to the pump making
sure that obstacles are not in between pump
and head.
BEEP
- check the identification number of the head
BEEP
and of the pump reported on the tag.
- check again the cable to be cut.
- repeat the cycle and if the problem persists
contact Cembre.
In order to reset the alarm press the release
button, connect the flexible hose or check the
correct connection to the pump.
Replace the battery.
If the problem persists, please contact
Cembre.
Remove and re-insert the battery, then re-start
the pump.
If the error occurs frequently, contact Cembre.
Remove and re-insert the battery, if the error
occurs, contact Cembre.
Repeat the work cycle; if the error occurs fre-
quently, contact Cembre.
Remove and re-insert the battery, then re-start
the pump.
If the error occurs frequently, contact Cembre.
002
003
003
004
004
S
olution
LED
OFF
LED
OFF
LED
ON
LED
ON
Advertisement
