Advertisement
6. INSTRUCTIONS FOR USE (Crimping operation)
The pump is suitable for use with Cembre KV type protected crimping heads.
1
*
The default settings of the pump are:
- Operating mode: CUTTING (Ref. to section 7.2 to choose CRIMPING operating mode).
- Oil release mode: SMART (Ref. to section 7.3 for further details).
2
- Pump control mode: RADIO ON, operated by radio remote control only (Ref. to section 7.4 for
*
further details).
For a crimping operation select the crimping mode via the display, before starting any
3
crimping operations.
When the crimping mode is active, the LED light (4) and the buzzer (5) are deactivated.
When the battery is removed from the pump or after 1hour of inactivity (display OFF),
4
once you wake the pump up, it will always start with the default setting:
CUTTING MODE, SMART RELEASE and RADIO ON.
5
Connect the flexible hose, first to the head and then to the pump.
Press the control button (12) on the pump once to activate the pump, display ON.
Switch on the radio control by pressing the ON/OFF button (1).
Press the pump button (2), this activates the motor of the pump that feeds the
6
*
hydraulic head connected to it, pressurising the oil.
Once the set pressure (P
tomatically, the display will briefly show the maximum pressure reached
(P
) followed by "OK" to confirm the correct operation.
p
7
*
Releasing the pump button before the automatic stopping of the motor will
cause the pump to stop, keeping the oil pressure stable (P
pressure level. To complete the operation press the pump button
once more until the motor stops automatically.
8
*
At the end of the cycle, releasing the pump button will start the automatic
release of the ram and will allow return of the oil to the oil reservoir in the
pump (Ref. to section 7.3 for further details).
9
*
The display "ERROR" combined with 3 beeps and the LED flashing, indi-
P
= 729 bar
n
cates an incorrect crimping procedure; the oil return phase occurred
P =
0 bar
too early without waiting for the motor to be automatically switched
off and therefore the minimum set pressure was not reached.
10
Repeat the crimping cycle by holding down the start button until the motor is automatically
P
P
= 10573 psi
n
switched off.
P =
0 psi
P
When a crimping head is used, always press and hold the pump button until the motor stops
automatically.
P
= 729 bar
n
OK
P =
.... bar
P =
0 bar
P =
0 psi
RC ON
BATTERY
) is reached the pump will be switched off au-
n
10
29990
B68RC
17AW125
60°
P
= 729 bar
max 90°
n
P =
0 bar
RESET
SW:S1J76202
= 729 bar
n
= 731 bar
p
P
= 729 bar
n
OK
P = 0 bar
P
= 325 bar
p
RC OFF
) at its current
p
BATTERY
BATTERY
P
P
= 729 bar
n
P =
P =
0 bar
P
P
= 10573 psi
n
n
P =
0 psi
P
p
P
= 729 bar
P
n
OK
P =
.... bar
P = 0 bar
P
P
60
P =
P
59
n
P
p
58
P
.........
01
30001
LED
ON
RESET
SW:S1J41405
90°
max 90°
20
= 729 bar
n
0 bar
= 729 bar
= 731 bar
= 729 bar
n
OK
= 325 bar
p
= 729 bar
n
0 bar
= 729 bar
= 731 bar
= 729 bar
n
OK
OK
SAVE 60%
ERROR
100
001
002
003
NTC
004
FAULT
Advertisement
