Advertisement
P
= 729 bar
n
0 psi
P
= 731 bar
p
3
7.4) Change the "pump control mode"
P
= 729 bar
n
Control mode
OK
4
RADIO ON
default setting
P = 0 bar
RC ON
5
RADIO OFF
P
= 325 bar
p
To change the "pump control mode", proceed as follows:
- Select screen 5 from the "main menu" (Ref. to section 7.1), hold the finger on the touch button (9) until a
6
*
confirmation "beep" is heard, the choice made is shown by the related pictogram.
BATTERY
P
= 729 bar
n
When the battery is removed from the pump or after 1 hour of inactivity (display OFF),
60
P =
0 bar
once you wake the pump up, it will always start with the default setting, RADIO ON.
7
*
29990
7.5) Alarms / Warning / Notification
P
= 729 bar
59
n
These appear on the display during operation or at the end of the cycle, informing the operator
P
= 731 bar
p
on the state of the pump. It can be combined with beeps.
B68RC
8
*
17AW125
58
P
= 729 bar
Message
n
OK
60°
.........
9
*
max 90°
01
OK
SAVE 60%
BATTERY
RESET
10
BATTERY
SW:S1J76202
BATTERY
BATTERY
BATTERY
100
BATTERY
30001
30001
BATTERY
LED
BATTERY
ON
RESET
RESET
SW:S1J41405
30001
SW:S1J41405
30001
NTC
90°
FAULT
90°
BATTERY
max 90°
RESET
max 90°
RESET
SW:S1J41405
SW:S1J41405
90°
BATTERY
90°
max 90°
max.
max 90°
max.
30001
BATTERY
BATTERY
LED
RESET
LED
max.
ON
SW:S1J41405
max.
ON
LED
BATTERY
4
Associated pictogram
RC ON
5
RC OFF
6
*
BATTERY
7
*
29990
10
B68RC
8
*
17AW125
60°
9
*
max 90°
Meaning
RESET
10
CUT
SW:S1J76202
SUCCESSFULLY
COMPLETED
ERROR
ERROR
001
BATTERY
ERROR
001
LOW
ERROR
002
002
BATTERY
LED
TEMPERATURE
001
OFF
003
001
HIGH
003
002
004
MOTOR-PUMP
002
004
TEMPERATURE
ERROR
HIGH
003
003
INSUFFICIENT
004
OIL
004
001
min.
min.
REQUEST
002
MAINTENANCE
BATTERY
BATTERY
LED
003
LED
min.
OFF
min.
OFF
004
LED
BATTERY
BATTERY
P
= 729 bar
n
OK
30001
P =
.... bar
Control of the pump by means of radio control RRC1 only.
RC OFF
RESET
The control button (12) of the pump is disabled, except
SW:S1J41405
for waking up the pump.
Control of the pump by means of the control button (12) of
90°
the pump only. The radio control receiver and the radio
control RRC1 are disabled.
max 90°
10
max.
BATTERY
LED
ON
LED
OFF
The cutting operation completed successfully, the confirmation of a
successful cutting operation is dependent on two control mechanisms:
1) the pressure reached is >100 bar.
2) the correct signal from the blade travel sensor is received
Upon completion of a successful cutting operation, the display will
show the amount of energy saved during the cutting cycle due to
the pump not having to develop maximum pressure before both of
the above control mechanisms were met (Ref. to section 7.8).
Replace or recharge the battery. NOTE: when the battery voltage falls
BEEP
below a minimum safety threshold, the pump will not start, although
it is still possible to end a work cycle in progress.
Pump's LED light flashes quickly (0.1 s ON 0.1 s OFF) and the buzzer
emits a coordinated audible signal.
Remove the battery and wait until it cools down. In order to cool it
faster, it is possible to insert it into the battery charger supplied, thus
making use of the specific "AIR COOLED" function.
The maximum permitted operating temperature of 90 °C (194 °F) has
been reached. The pump stops; in this instance wait for it to cool
down. Only when the permitted working temperature is reached will
it be possible to re-use the pump.
This appears when the pressure of the hydraulic circuit doesn't
increase but remains near to zero for a duration of 60 consecutive
seconds.Check the oil level and if necessary refill (Ref. to section 8.4).
Number of cycle to recommended maintenance interval reached; the
pump continues to work, however, it is recommended that it is sent
to Cembre for a complete overhaul (Ref. to section 9).
P
= 729 bar
001
n
P =
.... bar
OK
002
Function
P = 0 bar
003
004
P
= 325 bar
p
P
= 729 bar
n
60
P =
0 bar
min.
P
= 729 bar
59
n
P
= 731 bar
p
BATTERY
LED
58
P
= 729 bar
n
OFF
OK
.........
Description
LED
01
ON
BEEP
OK
SAVE 60%
100
LED
ON
NTC
FAULT
P = 0 bar
P
= 325 bar
p
P
= 729 bar
n
60
P =
0 bar
P
= 729 bar
59
n
P
= 731 bar
p
58
P
= 729 bar
n
OK
.........
01
OK
SAVE 60%
100
LED
ON
LED
NTC
OFF
FAULT
24
LED
ON
LED
OFF
Advertisement
