Advertisement
5. INSTRUCTIONS FOR USE (Cutting operation)
Cutting operations must be strictly in accordance with the
safety and working procedures established by the respon-
sible power utility.
STEP 1- Checking and testing the unit prior to cutting operations
Check all components (cutting head, flexible hose, couplings and pump) before use to verify there
is no damage or leakage.
Proceed as follow:
Check the battery charge and recharge it if necessary following the instructions in the battery
charger user manual. When a cutting operation begins, a check is made from the electronic
card to determine whether the battery charge is sufficient to complete the cutting operation.
If this is not the case the pump does not start. The LED (4) light will FLASH intermittently
and the buzzer (5) will emit an audible signal coordinated with the LED light.
Remove the battery from the pump (Ref. to Fig. 5).
Connect the flexible hose first to the cutting head and then to the
pump (Ref. to Fig. 6).
Insert the battery into the pump.
P =
0 bar
Activate the pump by pressing forward the control button (12) on
1
*
the pump, the display lights up and the pump setting is displayed.
Turn on the radio control by pressing the ON/OFF button (1), the LED will
flash green, after 3 minutes the radio control automatically switches off.
P =
0 psi
2
*
Press the pump button (2) on the radio control to perform a test cutting
operation. During the operation the pump's LED light will FLASH
intermittently and the buzzer will emit an audible signal coordinated with the LED light.
3
At the end of the operation the pump will stop, the LED will remain a STEADY LIGHT (2 minutes)
and the speaker will emit a COUNTINUOUS BUZZER sound (30 seconds). This confirms the pump
received a signal from the cutting head acknowledging that the blades
4
are completely closed; the display will show the following flashing screen
(Ref. to section 7.5 for further details).
Release the finger from the pump button (2) to initiate the SMART RELEASE function of the pump;
the operator should then check to ensure the blades are fully retracted to the start position.
RC ON
5
Remove the battery from the pump.
Disconnect the flexible hose from the pump and cutting head.
6
*
BATTERY
17
10
7
*
P =
0 bar
1
*
P =
0 psi
2
*
3
4
RC ON
5
6
*
BATTERY
10
7
*
29990
B68RC
8
*
17AW125
60°
9
*
max 90°
RC OFF
RESET
10
SW:S1J76202
RC OFF
P
P
= 729 bar
n
P =
P =
0 bar
P
P
= 10573 psi
n
n
P =
0 psi
P
p
P
= 729 bar
P
n
OK
P =
.... bar
P = 0 bar
P
P
60
P =
P
59
n
P
p
P
P
= 729 bar
n
P =
P =
0 bar
P
P
= 10573 psi
n
P =
0 psi
P
P
= 729 bar
P
n
OK
P =
.... bar
= 729 bar
n
P
60
0 bar
P =
= 729 bar
P
59
= 731 bar
P
= 729 bar
n
58
P
OK
.........
01
= 325 bar
p
= 729 bar
n
0 bar
= 729 bar
= 731 bar
= 729 bar
n
0 bar
= 729 bar
n
= 731 bar
p
= 729 bar
n
OK
P = 0 bar
12
P
= 325 bar
p
= 729 bar
n
0 bar
= 729 bar
n
= 731 bar
p
= 729 bar
n
OK
OK
SAVE 60%
100
LED
ON
LED
B
B
LE
O
Advertisement
