Advertisement
7.3) Change the "release mode"
P =
0 bar
1
*
The method of discharging the oil into the pump's tank can be carried out in two different ways,
depending on the mode set in the menu:
P =
0 psi
Release mode
2
*
SMART
default setting
3
P
P
= 729 bar
4
MANUAL
n
n
P =
0 bar
P =
To change the "release mode", proceed as follows:
P
P
= 10573 psi
RC ON
n
n
5
- Select screen 4 from the "main menu" (Ref. to section 7.1), hold the finger on the touch button(9) until a
P =
0 psi
P
p
confirmation "beep" is heard, the choice made is show by the related pictogram.
When the battery is removed from the pump or after 1 hour of inactivity (display OFF),
P
= 729 bar
P
n
n
6
*
once you wake the pump up, it will always start with the default setting, SMART MODE.
OK
OK
BATTERY
P =
.... bar
10
7.3.1) Extended release phase
P = 0 bar
7
*
29990
f necessary, the phase of discharging the oil into the pump's tank can be extended, leaving the
I
release valve open for 60 seconds.
This function is useful in the event that the blades are jammed after the cutting operation. It allows
P
B68RC
the operator to work on the cutting head using both hands in case of a blade jamming.
8
*
17AW125
To activate "extended release" proceed as follows:
P
- Press quickly (3 times within 2 seconds) the release button on the radio control
n
60
60°
P =
RRC1 or the button (12) backward on the pump if RC mode is disabled.
9
*
max 90°
The operation is then reported on the display by a counter associated with an
intermittent buzzer.
P
59
n
- In order to stop the countdown before reaching zero, press the pump button
P
RESET
p
10
on the radio control once for 2 seconds.
SW:S1J76202
58
P
n
OK
.........
01
23
LED
ON
P =
0 psi
2
*
3
Associated pictogram
4
RC ON
5
= 729 bar
0 bar
6
*
= 729 bar
RC OFF
BATTERY
= 731 bar
10
= 729 bar
7
*
29990
B68RC
8
*
17AW125
60°
9
= 325 bar
*
p
max 90°
= 729 bar
RESET
10
0 bar
SW:S1J76202
= 729 bar
= 731 bar
= 729 bar
OK
SAVE 60%
100
LED
OFF
P
= 729 bar
n
P =
0 bar
P
= 10573 psi
n
P =
0 psi
By releasing the pump button the oil is returned in full to
the pump reservoir only following automatic shut-off of
P
= 729 bar
the motor.
n
OK
During the return phase, pressing the buttons allows the
head ram retraction to be interrupted at any point.
To return the oil to the pump reservoir it is necessary to
RC OFF
P =
.... bar
press and hold the release button.
During the return phase, by releasing the button it is pos-
BATTERY
sible for head ram retraction to be interrupted at any point.
BATTERY
60
RESET
SW:S1J41405
59
90°
max 90°
58
.........
01
max.
BATTERY
LED
ON
LED
OFF
BEEP
P =
0 bar
P
= 10573 psi
n
P
= 729 bar
n
P =
0 psi
P =
0 bar
P
= 729 bar
n
P
= 729 bar
OK
n
Function
P
= 731 bar
p
P =
.... bar
P
= 729 bar
n
OK
P = 0 bar
ERROR
60
P
= 325 bar
p
59
30001
P
= 729 bar
n
P =
0 bar
58
P
= 729 bar
n
P
= 731 bar
p
.........
01
P
= 729 bar
n
OK
OK
min.
SAVE 60%
BATTERY
100
BEEP
LED
ON
NTC
FAULT
P
= 729 bar
n
P
= 731 bar
p
P
= 729 bar
n
OK
P = 0 bar
P
= 325 bar
p
P
= 729 bar
n
P =
0 bar
001
P
= 729 bar
n
P
= 731 bar
002
p
003
P
= 729 bar
n
OK
LED
004
ON
OK
LED
SAVE 60%
OFF
100
LED
LED
OFF
ON
LED
ON
NTC
LED
FAULT
OFF
Advertisement
