Novexx Solutions 64 Series User Manual
  1. Manuals
  2. Brands
  3. Novexx Solutions Manuals
  4. Printer Accessories
  5. 64- series
  6. User manual

Novexx Solutions 64 Series User Manual

Dispenser
Hide thumbs Also See for 64 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
03/13 Rev. 5.08-01
Servicing and Maintenance
General Notes ................................................ 2
Servicing by trained personnel ................... 2
Safety ......................................................... 2
Fault correction .......................................... 2
Ordering spare parts .................................. 3
Servicing and cleaning ................................... 4
Notes for cleaning ...................................... 4
Cleaning agents ......................................... 4
Printhead ........................................................ 5
Cleaning the print head .............................. 5
Changing the print head ............................. 6
Checking the print head ............................. 7
USER MANUAL
64-xx - 64-xx Dispenser
Rubber rollers .................................................9
Cleaning the print roller ...............................9
Cleaning the feed roller .............................10
Photoelectric switches ..................................12
switch ........................................................12
Cleaning the cutter .......................................13
Important notes .........................................14
Exchanging the filter liner ..........................14
Index .............................................................15

Advertisement

Table of Contents
loading

Related Manuals for Novexx Solutions 64 Series

Summary of Contents for Novexx Solutions 64 Series

  • Page 1: Table Of Contents

    03/13 Rev. 5.08-01 USER MANUAL 64-xx – 64-xx Dispenser Servicing and Maintenance General Notes ..........2 Rubber rollers ..........9 Servicing by trained personnel ....2 Cleaning the print roller .......9 Safety ............2 Cleaning the feed roller ......10 Fault correction .......... 2 Cleaning the dispenser-feed-roller ....11 Ordering spare parts ........

  • Page 2: General Notes

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser General Notes Servicing by trained personnel Regular and proper servicing is necessary in order to ensure that the device is permanently ready for operation. Qualification Servicing and repair work may only be carried out by appropriately qualified personnel.

  • Page 3: Ordering Spare Parts

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Ordering spare parts  Only use original spare parts from the manufacturer. The use of parts which do not satisfy the high demands set by the printer manufacturer can cause unnecessary problems.

  • Page 4: Servicing And Cleaning

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Servicing and cleaning Notes for cleaning Intervals Regular servicing and cleaning work is necessary for safe operation and high running performance. The servicing intervals are dependent on the operation and ambient conditions, daily operating times and the print medium.

  • Page 5: Printhead

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Printhead Cleaning the print head 1. Switch off the device. 2. Pull out the mains plug. 3. Remove material and ribbon. 4. Unscrew the two thumb screws on the print head mounting until the entire printhead mounting can be rotated upwards on the contact shaft.

  • Page 6: Changing The Print Head

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Changing the print head The print head is adjusted to the print head mounting during manufacture. As a result the print head can only be replaced in conjunction with the print head mounting.

  • Page 7: Checking The Print Head

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser  Entering a false value can damage the print head!  Please also read the Service Manual, topic section "Service print module", paragraph "Exchanging the printhead".  If the printout is worse than before, after a new printhead was installed, the printhead position has possibly to be adjusted.
  • Page 8 03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser  64-08 printers need up to 40 min time to perform a dot check. For this reason, it is not recommended to use the "Automatic dot check" mode with this type of printer.

  • Page 9: Rubber Rollers

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Rubber rollers Cleaning the print roller 1. Switch off the device. 2. Pull out the mains plug. 3. Remove material and ribbon. 4. Only dispenser version: Remove the dispensing edge to gain easier access to the print roller.

  • Page 10: Cleaning The Feed Roller

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser  CAUTION! - Only clean the print roller with a dust-free cloth and roller cleaner. Never use knives or sharp-edged objects to clean the rollers! Keeping impurities and dirt of any description away from the printing area generally increases the running performance of the printer, and especially that of the print head.

  • Page 11: Cleaning The Dispenser-Feed-Roller

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser 7. After cleaning, return the print head mounting to its old position and retighten the thumb screws.  Press the thumb screw on the tapered edge of the square axle and ensure the exact positioning of the print head mounting on the axle.

  • Page 12: Photoelectric Switches

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Photoelectric switches Cleaning the gap photoelectric switch 1. Switch off the device. 2. Pull out the mains plug. 3. Remove material and ribbon. 4. Unscrew the two thumb screws on the print head mounting the entire print head mounting can be rotated upwards on the contact shaft.

  • Page 13: Cleaning The Cutter

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Cleaning the cutter  Only with cutter option! WARNING! Sharp blades may cause cut injuries at hands and fingers!  Take the utmost caution when cleaning the cutters! ...

  • Page 14: Cleaning/Exchanging The Dust Filter Liner

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Cleaning/exchanging the dust filter liner Important notes The dust filter is an option (article number A9344). The filter is mounted in front of the fan opening at the printer rear side. ...

  • Page 15: Index

    03/13 Rev. 5.08-01 USER MANUAL Servicing and Maintenance 64-xx – 64-xx Dispenser Index Changing the print head ......6 Material end photoelectric switch ....12 Charges, electrostatic ......5, 6 Material feed ..........12 Cleaning ............4 - knife ............13 Neutral cleaning agents ......

Table of Contents