Table of Contents
Advertisement
Quick Links
04/09 Rev. 5.01-02
Fault Location
Error sources ................................................ 2
Notes about fault location .......................... 2
Data transmission ..................................... 2
Display ...................................................... 2
Gap detection ............................................ 2
Material transport ...................................... 3
Ribbon, ribbon guide ................................. 3
Print roller .................................................. 3
Position of the print image ......................... 4
Print quality ............................................... 4
Plug-in card (AP 5.4/AP 7.t) ....................... 5
Cut function, cutter (AP 5.4/AP 7.t) ............ 5
Cut function, TCS (AP 7.t) ......................... 6
SERVICE MANUAL
AP 4.4 - AP 5.4 - AP 7.t
Reading out diagnosis data ...........................7
Reading out via serial interface .................8
Storing on CF card ...................................10
Advertisement
Table of Contents
Related Manuals for Novexx Solutions AP 4.4
Summary of Contents for Novexx Solutions AP 4.4
-
Page 1: Table Of Contents
04/09 Rev. 5.01-02 SERVICE MANUAL AP 4.4 – AP 5.4 – AP 7.t Fault Location Error sources ..........2 Reading out diagnosis data ......7 Notes about fault location ......2 Reading out via serial interface ....8 Data transmission ........2 Storing on CF card ........10... -
Page 2: Error Sources
04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t Error sources Notes about fault location Status reports should be printed to check the mechanical and electronic function capabilities – provided that no obvious no defectives are evident. -
Page 3: Material Transport
04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t Problem Possible cause Solution Print position shifted Gap position not recog- Correct photoelectric switch zero line using in or against print di- nised consistently due to PRINT PARAMETERS >... -
Page 4: Position Of The Print Image
04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t Problem Possible cause Solution Ribbon prints directly on Ink residue Clean and prevent direct printing on roller feed roller Printing directly on roller Use sufficient wide material/foil... -
Page 5: Plug-In Card (Ap 5.4/Ap 7.T)
04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t Problem Possible cause Solution Check setting print contrast (press Prog. but- ton in on-line mode or parameter Printhead setting too low PRINT PARAMETER > Print contrast) and if nec. -
Page 6: Cut Function, Tcs (Ap 7.T)
04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t Cut function, TCS (AP 7.t) Problem Possible cause Solution Connector loose Plug in connector firmly. Select and activate "TCS" setting for parame- TCS function not activated SYSTEM PARAMETER >... -
Page 7: Reading Out Diagnosis Data
04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t Reading out diagnosis data With the diagnose dump function, device inter- nal operation states can be read via serial con- nection and be saved in a text file. This way, the... -
Page 8: Reading Out Via Serial Interface
04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t Reading out via serial interface Prerequisites • Firmware (at least): Version Printing device 3.22 AP 4.4 (16 MB), AP 5.4, AP 7.t 4.22 64-xx Gen. 2, DPM, ALX 92x 5.02... - Page 9 04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t [4] Read out data. Send the generated files with a descriptioin of the circumstances in which the error occured per email to the technical support at Avery Den-...
-
Page 10: Storing On Cf Card
04/09 Rev. 5.01-02 SERVICE MANUAL Fault Location AP 4.4 – AP 5.4 – AP 7.t Storing on CF card Prerequisites Firmware (at least): Version Printing device 3.31 AP 4.4 (16 MB), AP 5.4, AP 7.t 4.31 64-xx Gen. 2, DPM, ALX 92x 5.31...