Powering On In Standby Mode; Powering Off; Navigating Menus; Locking/Unlocking Changes To Settings - Lectrosonics LMb Instruction Manual

Powering On in Standby Mode

A brief press of the Power Button
before the counter has reached 3, will turn the unit on
with the RF output turned off. In this Standby Mode,
the menus can be browsed to make settings and
adjustments without the risk of interfering with other
wireless systems nearby.
Release Power
Hold
Button before
for the counter
reaches 3 to
Rf On
enter standby
...1
After settings and adjustments are made, press the
power button again to turn the unit off.
NOTE: Also see the section entitled Power
Menu for the AutoOn feature.

Powering Off

From any screen, power can be
Powering
turned off by selecting Pwr Off in
O . . .
the power menu or holding the
Power Button
the countdown, EXCEPT if the top
panel switch is configured for this
1
function.
If the power button is released, or the top panel
switch is turned back on again before the countdown
is completed, the unit will remain turned on and the
LCD will return to the same screen or menu that was
displayed previously.
NOTE: When the top panel switch is configured
as a power switch, that is the only way to turn
the unit off.

Navigating Menus

The LCD and keypad interface make it easy to
browse the menus and make the selections for the
setup the user needs. When the unit is powered up
in either the operating or the standby mode, press
MENU/SEL on the keypad to enter a menu structure
on the LCD. Use the
the menu item. Then press the MENU/SEL button to
enter the menu.
Gain
Freq.
ProgSw
Compat
The prompt in the upper right corner may
display one or both arrows, depending upon
what adjustment can be made. If the changes
are locked, a small padlock symbol will appear.
Rio Rancho, NM
, releasing it
RF indicator blinks
b 19
5 1
494.500
mode
-40 -20
in and waiting for
and arrow buttons to select
Gain
25
-40 -20 0
Digital Hybrid Wireless
Locking/Unlocking Changes to
Settings
Changes to the settings can be locked.
StepSiz
Phase
Locked
Backlit
A small padlock symbol will appear on adjustment
0
When changes are locked, several controls and ac-
tions can still be used:
• Settings can still be unlocked
• Menus can still be browsed
• Programmable switch still works
• Power can still be turned off by using the power
menu or removing the batteries.

Power Menu Options

A special options menu is provided by pressing the
power button
in either the Operating or Standby modes. Use the
and arrow buttons to select the menu item.
• Resume - returns to the previous mode and
screen
• Pwr Off - turns the unit off
• Rf On? - enters a screen to enable the operating
or standby modes
• AutoOn? - allows the unit to automatically turn
back on after a power failure or when fresh bat-
teries are installed (works in the operating mode
only)
• Backlit - adjusts the duration of the LCD back
light to 30 seconds or 5 minutes, or to remain on
• LED Off - turns the LEDs on (Normal) or off (Dark)
• About - displays the installed firmware version
• Blk606? - Band B1 and C1 LMb transmitters
can be used with legacy Block 606 Lectrosonics
receivers by invoking a special Block 606 legacy
mode (Introduced in Firmware version v2.12) so
that the correct pilot tones will be present. Use
the and
press MENU/SEL to save.
NOTE: Neither Band B1 nor Band C1 includes
all Block 606 frequencies.
"Legacy" refers to SRb/E01-606 receivers, as
well as the original Venue (VRMWBL with VRS/
E01-606 modules).
®
UHF Belt Pack Transmitter
Locked?
No
Yes
screens when changes have been locked.
quickly when the unit is turned on
arrow buttons to select Legacy and
Gain
25
-40 -20 0
7