Install Filter; Replacing The Water Softener Filter; Adjust Time; Auto-Start - DeLonghi Eletta ECAM45.760.W Manual

To enable the function, proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Rinsing" appears on
h
the display (B13);
3. Press the OK button (B12-fig. 10): the message "Confirm?"
c
is displayed;
-
Danger of burns!
Do not leave the appliance unattended while hot water is being
delivered.
4. Press the OK button. "RINSING Please wait" is displayed;
d
5. After a few seconds, hot water is delivered first from the
coffee spouts, then from the hot water/steam spout (if in-
.
serted) to heat the appliance's internal circuit. "RINSING" is
e
displayed, together with a progress bar which fills gradual-
ly as preparation proceeds;
.
6. To stop the process press any button or wait for delivery of
s
water to stop automatically.
Please note!
• If the appliance is not used for more than 3-4 days, when
switched on again, we strongly recommend performing
2/3 rinses before use;
• After cleaning, it is normal for the grounds container (A10)
to contain water.
8.2 Descaling
s
For instructions on descaling, see section "13. Descaling".
.

8.3 Install filter

For instructions on how to install the filter, see section "15.
e
Water softener filter".
a
8.4 Replacing the water softener filter (if
installed)
For instructions on how to replace the filter, see section "15.2
g
Replacing the filter".

8.5 Adjust time

e
To adjust the time on the display (B13), proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Adjust time" is
displayed;
3. Press the OK button (B12-fig. 10): the hours flash on the
display;
4. Press < or > to change the hour;
5. Press the OK button to confirm. The minutes flash;
n
6. Press < or > to change the minutes;
7. Press the OK button to confirm.
The time is set. Press the MENU/ESC button to exit the menu.

8.6 Auto-start

You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coffee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Auto-start" appears on
the display (B13);
3. Press the OK button (B12- fig. 10). "Enable?" is displayed;
4. Press the OK button to confirm;
5. Press < or > to choose the hour;
6. Press the OK button to confirm;
7. Press < or > to change the minutes;
8. Press the OK button to confirm;
9. Press the MENU/ESC button to exit the menu.
Once the time has been confirmed, activation of auto-start is
indicated by the symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the OK button. "Disable?" is displayed;
3. Press the OK button to confirm.
The symbol is no longer displayed.

8.7 Auto-off (standby)

Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-off, proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Auto-start" appears on
the display (B13);
3. Press the OK button (B12- fig. 10);
4. Press < or > until the required operating time (15 or 30
minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button to confirm;
6. Press the MENU/ESC button to exit the menu.
Auto-off is now programmed.

8.8 Cup warmer

This function enables the cup warmer to be enabled or disabled.
Proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (fig. 9) until "Cup warmer" appears
on the display (B13);
3. Press the OK button (B12- fig. 10). "Enable?" or "Disable?"
is displayed;
119