Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
PUPPY AND GARDEN
VINYL GATE KIT
(301/2"H X 551/2"W)
Approximate assembly time
Want to see a video on how to
WWW.ZIPPITY-OUTDOOR.COM
WWW.ZIPPITY-OUTDOOR.COM
BELLA
60 MIN
assemble this product?
Scan the QR code
ASSEMBLY
INSTRUCTIONS
ZP19070
ZP19070
1
VER. 020821
Advertisement
Related Manuals for Zippity BELLA ZP19070
Summary of Contents for Zippity BELLA ZP19070
- Page 1 ZP19070 ASSEMBLY INSTRUCTIONS BELLA ASSEMBLY INSTRUCTIONS PUPPY AND GARDEN VINYL GATE KIT ZP19070 (301/2”H X 551/2”W) 60 MIN Approximate assembly time Want to see a video on how to assemble this product? Scan the QR code WWW.ZIPPITY-OUTDOOR.COM WWW.ZIPPITY-OUTDOOR.COM VER. 020821...
- Page 2 If you experience any further trouble with your product, please contact our customer service department. parts.nychbrands.com support@zippity-outdoor.com 704-892-5222 877-234-6196 Customer service agents are available to take calls weekdays from 9am- 5pm EST. If you call outside of business hours, please leave a voicemail.
- Page 3 ZP19070 ASSEMBLY INSTRUCTIONS 37.1in 1.2in spacing Ground WWW.ZIPPITY-OUTDOOR.COM...
- Page 4 1½” x 1½” x 37” Steel Screw (14) 3/4” Self-Tapping Stainless Steel Screw (24) Wing Post (4) Post (2) Picket (10) 1/16” Drill Bit (1) ⅞” x 1½” x 42” ⅞” x 1½” x 28⅞” 3/8” x 23/4” x 27” WWW.ZIPPITY-OUTDOOR.COM...
- Page 5 Note: It is recommended to lay the product on the floor or other flat surface for this step. Align Align Leave screw off here for latch installation. WWW.ZIPPITY-OUTDOOR.COM...
- Page 6 Drive (4) total 1/2” Black Self-Tapping Steel Screw into the rails to secure the hinges. Note: Install the hinges on the right side of the panel if you wish to have a left-hand operation gate. WWW.ZIPPITY-OUTDOOR.COM...
- Page 7 Slide (1) Wing Bottom Rail over the bottom of the wing posts until the pre-drilled holes in the wing bottom rail and bottom of wing posts align. Align Align WWW.ZIPPITY-OUTDOOR.COM...
- Page 8 Insert (1) picket into the routed holes in the top and bottom rail until the tabs of the picket lock into the bottom rail. STEP 3.3 Repeat Steps 3.1 - 3.2 to assemble the second gate wing. WWW.ZIPPITY-OUTDOOR.COM...
- Page 9 Add water to soften the soil. Use a block of wood to protect the top of the wing post and gently hammer each wing post into the ground until the bottom wing rails are roughly 2” above the ground. WWW.ZIPPITY-OUTDOOR.COM...
- Page 10 Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated ($15-$20 on Amazon.com). Drill a hole about 12” to 16” deep at the desired location, and fill the holes with water as illustrated. Push the wing posts into the holes. WWW.ZIPPITY-OUTDOOR.COM...
- Page 11 INSTALL THE GATE HARDWARE STEP 5: STEP 5.1 Align the hinges against the wing rails of the gate wing as shown. Mark and pre-drill two holes for each hinge. Fasten each hinge with (2) 1/2” black self-tapping steel screws. WWW.ZIPPITY-OUTDOOR.COM...
- Page 12 Fasten with (2) 1/2” black self-tapping steel screws. STEP 5.3 Drive the 3/4” self-tapping stainless steel screws and the joiner clips included with your fence kits to connect the gate wings to the fence panels as shown below. WWW.ZIPPITY-OUTDOOR.COM...
- Page 13 ZP19070 ASSEMBLY INSTRUCTIONS INSTALL POST CAPS STEP 6: STEP 6.1 Insert (6) Post Caps over the tops of the gate wing and gate panel posts. WWW.ZIPPITY-OUTDOOR.COM...
- Page 14 ZP19070 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 support@zippity-outdoor.com 704-892-5222 877-234-6196 WWW.ZIPPITY-OUTDOOR.COM WWW.ZIPPITY-OUTDOOR.COM...