Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
HUNTERSVILLE
VINYL SCREEN
Approximate assembly time for 2 screens
If necessary, this screen can be
your custom space. Use a fine-toothed circular or hack saw.
Rails will need to be re-spaced and configured accordingly.
Want to see a video on how to
WWW.ZIPPITY-OUTDOOR.COM
WWW.ZIPPITY-OUTDOOR.COM
2-PACK
(36" W X 45" H)
60 MIN
trimmed down vertically
to fit
assemble this product?
Scan the QR code
ASSEMBLY
INSTRUCTIONS
ZP19036
ZP19036
1
VER. 031121
Advertisement
Related Manuals for Zippity HUNTERSVILLE ZP19036
Summary of Contents for Zippity HUNTERSVILLE ZP19036
- Page 1 Use a fine-toothed circular or hack saw. Rails will need to be re-spaced and configured accordingly. Want to see a video on how to assemble this product? Scan the QR code WWW.ZIPPITY-OUTDOOR.COM WWW.ZIPPITY-OUTDOOR.COM VER. 031121...
- Page 2 If you experience any further trouble with your product, please contact our customer service department. parts.nychbrands.com support@zippity-outdoor.com 704-892-5222 877-234-6196 Customer service agents are available to take calls weekdays from 8am- 5pm EST. If you call outside of business hours, please leave a voicemail.
- Page 3 ZP19036 ASSEMBLY INSTRUCTIONS 36 in 7/8 in 1 1/2 in 33 3/8 in WWW.ZIPPITY-OUTDOOR.COM...
- Page 4 Picket #8 ¼” x 1¼” x 38⁹̸ ₁ ₆” ¼” x 1¼” x 36¹⁵̸ ₁ ₆” Note: the bottom rail only has holes on one side. Bottom Rail (2) 1½” x 1½” x 36” 1/8" Steel Drill Bit (1) WWW.ZIPPITY-OUTDOOR.COM...
- Page 5 Fasten together using (8) locking tabs. ¾” self-drilling stainless steel screws (I). Align holes This will be the top of the screen. Tip: shine a flashlight down the end of the posts to help identify alignment of pre- drilled holes. WWW.ZIPPITY-OUTDOOR.COM...
- Page 6 Drive (4) 3/4" self-drilling stainless steel screws into the pre-drilled holes in the bottom rail. Note: If your ground is very Pickets 1,2,3, etc... hard, the anchor can be slid until the bottom of the anchor is 8” beyond the bottom of the posts. WWW.ZIPPITY-OUTDOOR.COM...
- Page 7 All 10” of the location of the posts. post anchors should be inserted into the ground, so that they are no longer visible Push down on the top of posts with both hands. WWW.ZIPPITY-OUTDOOR.COM...
- Page 8 Loosen the top 6” or 7” of the ground with a claw hammer as illustrated. Add water to loosen soil. Use a block of wood to protect the top of the post, and gently hammer the post into the ground. Block of wood WWW.ZIPPITY-OUTDOOR.COM...
- Page 9 Level STEP 4.5 If your ground is really hard, you may need to dig a hole large enough to accommodate one post from each screen into the same hole. Backfill and compact dirt. 8” diameter 10” deep. WWW.ZIPPITY-OUTDOOR.COM...
- Page 10 ZP19036 ASSEMBLY INSTRUCTIONS FASTEN JOINER CLIPS STEP 5: STEP 5.1 Fasten screens together by using (2) joiner clips and (4) 1” self-drilling stainless steel screws as illustrated. Bottom Rail Top Rail Angled Screens Application Corner Screens Application WWW.ZIPPITY-OUTDOOR.COM...
- Page 11 ZP19036 ASSEMBLY INSTRUCTIONS FASTEN POST CAPS STEP 6: STEP 6.1 Push the post caps down over the posts to lock into place. WWW.ZIPPITY-OUTDOOR.COM...
- Page 12 ZP19036 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 support@zippity-outdoor.com 704-892-5222 877-234-6196 WWW.ZIPPITY-OUTDOOR.COM WWW.ZIPPITY-OUTDOOR.COM...