Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
BURBANK
VINYL PICKET
FENCE 2-PACK
(44" W X 41"H)
Approximate assembly time for 2 panels
Want to see a video on how to
assemble this product?
Scan the QR code
WWW.ZIPPITY-OUTDOOR.COM
WWW.ZIPPITY-OUTDOOR.COM
45 MIN
ASSEMBLY
INSTRUCTIONS
ZP19057
ZP19057
1
VER. 081121
Advertisement
Related Manuals for Zippity BURBANK
Summary of Contents for Zippity BURBANK
- Page 1 ZP19057 ASSEMBLY INSTRUCTIONS BURBANK ASSEMBLY INSTRUCTIONS VINYL PICKET FENCE 2-PACK ZP19057 (44” W X 41”H) 45 MIN Approximate assembly time for 2 panels Want to see a video on how to assemble this product? Scan the QR code WWW.ZIPPITY-OUTDOOR.COM WWW.ZIPPITY-OUTDOOR.COM...
- Page 2 If you experience any further trouble with your product, please contact our customer service department. parts.nychbrands.com support@zippity-outdoor.com 704-892-5222 877-234-6196 Customer service agents are available to take calls weekdays from 9am- 5pm EST. If you call outside of business hours, please leave a voicemail.
- Page 3 ZP19057 ASSEMBLY INSTRUCTIONS 44 in 2 3/8 in 1 in WWW.ZIPPITY-OUTDOOR.COM...
- Page 4 1/4" x 11/4" x 38½" 7/8" x 1½" x 40½" Post Anchor (4) ¾" x 1¼" x 20" Horizontal Bottom Rail (2) Horizontal Top Rail (2) 1/8" Drill Bit 1½" x 1½" x 44" 1½" x 1½" x 44" WWW.ZIPPITY-OUTDOOR.COM...
- Page 5 Slide (1) top rail down over the posts until the Preview pre-drilled holes in the posts and top rail align. Drive (4) 3/4" Stainless Steel Screws into the pre-drilled holes in the top rail. Align Top of fence Post tabs WWW.ZIPPITY-OUTDOOR.COM...
- Page 6 STEP 3: STEP 3.1 Rotate the fence panel so the ground stakes face down. Insert (1) Picket into the rails until it locks in the bottom rail. Preview Insert (9) additional pickets into the pre-drilled holes in the rails. WWW.ZIPPITY-OUTDOOR.COM...
- Page 7 ZP19057 ASSEMBLY INSTRUCTIONS ASSEMBLE SECOND FENCE PANEL STEP 4: STEP 4.1 Repeat steps 2-3 to assemble the second fence panel. WWW.ZIPPITY-OUTDOOR.COM...
- Page 8 Loosen the top 6” or 7” of the ground with a claw hammer as illustrated. Add water to loosened soil. Use a block of wood to protect the top of post, and gently hammer the post into the ground. WWW.ZIPPITY-OUTDOOR.COM...
- Page 9 If the ground is too hard, you may need to dig a hole large enough to accommodate one post from each panel in the same hole, as shown below. 8" Diameter x 10" Deep STEP 5.4 Level the screen, backfill excavated dirt, and tamp as necessary. Level WWW.ZIPPITY-OUTDOOR.COM...
- Page 10 (4) 3/4" stainless steel screws as illustrated. Corner Application: Fasten screens together with Joiner Clips using (4) 3/4" stainless steel screws as illustrated. NOTE: Use the 1/8" drill bit to pre-drill holes in the rails as needed for joiner clip installation. WWW.ZIPPITY-OUTDOOR.COM...
- Page 11 ZP19057 ASSEMBLY INSTRUCTIONS INSTALL POST CAPS STEP 7: STEP 7.1 Push the Post Caps down over the posts to lock into place. WWW.ZIPPITY-OUTDOOR.COM...
- Page 12 ZP19057 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 support@zippity-outdoor.com 704-892-5222 877-234-6196 WWW.ZIPPITY-OUTDOOR.COM WWW.ZIPPITY-OUTDOOR.COM...