Table of Contents
Advertisement
Quick Links
Technical Manual
OPERATOR FOR SLIDING
SOCIAL DOOR
TORE
WARNING:
Do not use this device
Made by: Motoppar Indústria e Comércio de Automatizadores Ltda
without read the manual
Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil
instructions.
CNPJ: 52.605.821/0001-55
P09875 - 05/2022
Rev. 0
www.ppa.com.br | +55 14 3407 1000
28
1
Advertisement
Table of Contents
Related Manuals for PPA TORE
Summary of Contents for PPA TORE
- Page 1 Made by: Motoppar Indústria e Comércio de Automatizadores Ltda without read the manual Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil instructions. CNPJ: 52.605.821/0001-55 P09875 - 05/2022 Rev. 0 www.ppa.com.br | +55 14 3407 1000...
-
Page 2: Table Of Contents
Sizing of the door leaves ......................8 Drilling glass ........................10 Installation of the lock ......................10 Rail installation ........................11 Before using the TORE SOCIAL DOOR AUTOMATER, read and Glass installation .......................12 Flange and pulley assembly on the frame .................14 strictly follow all instructions contained in this manual. -
Page 3: Tools Requeired For Installation
TOOLS REQUIRED FOR INSTALLATION POWER CORD WITH GROUNDING PLUG For the installation of the operator, it is provided Ground connexion Below are some tools needed to install the operator: with a 3-pin plug. The middle pin is connected to the metal part of the operator, which connected to the socket is in direct contact with the network ground wire, increasing user safety. -
Page 4: Technical Characteristics
PICTURE 1 -5°C -5°C -5°C 2 Step: The Tore operator will be installed in a gap (directly on the ceiling): If it is directly on the ceiling (span), it will not need a structure (figure 2). +50 °C +50 °C +50 °C... -
Page 5: Sizing Of The Door Leaves
SIZING OF THE DOOR LEAVES c) The height of the movable leaf is the height of the right foot plus 45 mm, where the glass will be inside the rail. Ask to drill the hole according to the template. For the dimensioning of the door leaves, we must take into account the following aspects: a) How to calculate leaf size: Measure the span width, divide this value by the number of leaves you want, the... -
Page 6: Drilling Glass
2 Step: To fix the rail to the wall, measure the mobile leaf minus 45mm and fix the rail. Note: To purchase Bona Electromagnetic Lock, consult your PPA Distributor or 3 Step: Make marks on the wall to indicate the height of the base of the rail;... -
Page 7: Glass Installation
7 Step: Return the rail to the wall and just place the screws to support it (7°Step Fit part 1 in the hole of the movable glass, one on each side, then place part 2 will only be done if it is fixed in masonry). in the hole of part 1 and tighten with part 9. -
Page 8: Flange And Pulley Assembly On The Frame
FLANGE AND PULLEY ASSEMBLY ON THE FRAME RADAR 1 Step: To mount the cart on the frame profile, insert the cart already assembled Radar is a sensor that triggers the automatic door when an object approaches its into the frame as shown below in the illustration of this assembly process. detection radius. -
Page 9: Radar
Dip switch Configuration Fixing the radar to the cover Key 1 sets the state of the relay: ON = NC (normally closed) and OFF = NO 1. Radar must be fixed in the middle of the passageway. (normally open). Key 2 sets the pulse retention time: ON = 2 seconds and OFF = 0.5 seconds. Key 3 sets the immunity mode: ON = high immunity and OFF = normal immunity. -
Page 10: Photocell
PHOTOCELL CONNECTION DIAGRAM ON THE CONTROL BOARD Fixing and connecting the photocell 1. Pass cable 1 of 4-way going from the TX to the board, passing through the rail and fixed with clamps. 2. Pass cable 1 of 4-way going from RX to the board, passing through the rail and fixed with clamps.
Need help?
Do you have a question about the TORE and is the answer not in the manual?
Questions and answers