Table of Contents
Advertisement
Quick Links
Technical Manual
DZ BRUTALLE
WARNING:
Do not use the equipment
Made by: Motoppar Indústria e Comércio de Automatizadores Ltda
without first reading the
Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil
instruction manual.
CNPJ: 52.605.821/0001-55
P30452 - 04/2022
Rev. 1
www.ppa.com.br | +55 14 3407 1000
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PPA DZ BRUTALLE 3.0T JetFlex
Summary of Contents for PPA DZ BRUTALLE 3.0T JetFlex
- Page 1 Made by: Motoppar Indústria e Comércio de Automatizadores Ltda without first reading the Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil instruction manual. CNPJ: 52.605.821/0001-55 P30452 - 04/2022 Rev. 1 www.ppa.com.br | +55 14 3407 1000...
-
Page 2: Table Of Contents
INDEX IMPORTANT SAFETY INSTRUCTIONS ..................4 TECHNICAL CHARACTERISTICS ....................5 TOOLS REQUIRED FOR INSTALLATION ..................6 ELECTRICAL INSTALLATION ......................6 CARE WITH THE ELECTRICAL INSTALLATION ............... 7 GATE CARE BEFORE AUTOMATION ..................8 INSTALLATION AND FIXING OF THE OPERATOR ..............9 ANALOG LIMIT SWITCH INSTALLATION ................14 MAINTENANCE ..........................17... -
Page 3: Important Safety Instructions
Sliding Recommendation: MODEL JetFlex For the installation of the equipment, it is RATED VOLTAGE 127V / 220V important that the PPA specialized installer NOMINAL FREQUENCY 60 Hz RATED POWER 180W / 150W follow all the instructions mentioned in ENGINE ROTATION... -
Page 4: Tools Required For Installation
TOOLS REQUIRED FOR INSTALLATION CARE WITH THE ELECTRICAL INSTALLATION Below are some tools needed to install the operator: To avoid damage to the wiring, it is important that all conductors are correctly attached to the operator. The passage of the wiring must be done through conduits, passing internally through the base of the floor, ensuring that none of the wiring conductors is trapped and damaged. -
Page 5: Gate Care Before Automation
GATE CARE BEFORE AUTOMATION 3rd Step: Check that the gate leaf does not get stuck in the opening and closing movement. The gate’s sliding rail must be perfectly straight, level, periodically free of any element or dirt that makes it difficult for the pulleys to slide along their Before adapting the machine to the gate, check the slip, following the instructions entire length, as shown in the figure below. - Page 6 2nd Step: The dimensions of the base must be appropriate for the dimensions of 4th Step: Pre-align the operator to the gate, positioning the rack over the gear and the operator. The concrete base should be at a distance of approximately 20 mm leaning the set against the gate.
- Page 7 6th Step: With the operator unlocked, position the rack bar over the gear and 8th Step: If the gate leaf is warped, provide wedges to ensure rack alignment. aligned with the gate. There are cases where the rack will need to extend the length of the sheet. In this It is necessary to leave approximately a 2mm gap between the top of the rack tooth case, provide a French hand so that you do not jump your teeth when starting the and the bottom of the gear tooth.
-
Page 8: Analog Limit Switch Installation
ANALOG LIMIT SWITCH INSTALLATION 3rd Step: Start the engine and observe if the REED’s are shutting down correctly. If necessary, invert the board connector. Once the magnet supports are fixed, make the final adjustments, moving them to the right or left, down or up, according to the desired adjustment. 1st Step: With the gate closed, place the magnet support on the rack, positioned facing the operator’s REED. - Page 9 C) Defect in command board Technology: which is the operator board. Once this is C) Replace the command board Voltage: done, consult the board manual which Board: Size: is available for download at www.ppa. Mounting: Fairing: com.br and perform all connections and Gear: settings.
Need help?
Do you have a question about the DZ BRUTALLE 3.0T JetFlex and is the answer not in the manual?
Questions and answers