Advertisement
Technical manual
DZ RIO
WARNING:
Do not use the equipment
Made by: Motoppar Indústria e Comércio de Automatizadores Ltda
without first reading the
Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil
instruction manual.
CNPJ: 52.605.821/0001-55
P30454 - 04/2022
Rev. 0
www.ppa.com.br | +55 14 3407 1000
Advertisement
Table of Contents
Related Manuals for PPA DZ RIO
Summary of Contents for PPA DZ RIO
- Page 1 Made by: Motoppar Indústria e Comércio de Automatizadores Ltda without first reading the Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil instruction manual. CNPJ: 52.605.821/0001-55 P30454 - 04/2022 Rev. 0 www.ppa.com.br | +55 14 3407 1000...
-
Page 2: Table Of Contents
INDEX IMPORTANT SAFETY INSTRUCTIONS Recommendation: For the installation of the equipment, it is important that the PPA specialized installer follow all the instructions mentioned in this TECHNICAL MANUAL and in the USER MANUAL. IMPORTANT SAFETY INSTRUCTIONS ..................3 TECHNICAL CHARACTERISTICS ....................4... -
Page 3: Technical Characteristics
TECHNICAL CHARACTERISTICS DZ RIO 300 DZ RIO 350 DZ RIO 400 DZ RIO R 500 DZ RIO R 700 CUSTOM MONO MONO SP DZ RIO PREDIAL 800 DZ RIO PREDIAL 700 TYPE OF OPERATOR SLIDING SLIDING SLIDING SLIDING SLIDING JETFLEX... -
Page 4: Tools Required For Installation
TOOLS REQUIRED FOR INSTALLATION CARE WITH THE ELECTRICAL INSTALLATION Below are some tools needed to install the operator: To avoid damage to the wiring, it is important that all conductors are correctly attached to the operator. The passage of the wiring must be done through conduits, passing internally through the base of the floor, ensuring that none of the wiring conductors is trapped and damaged. -
Page 5: Gate Care Before Operation
GATE CARE BEFORE OPERATION 3rd Step: Check that the gate leaf does not get stuck in the opening and closing movement. The gate’s sliding rail must be perfectly straight, level, periodically free of any element or dirt that makes it difficult for the pulleys to slide along their Before adapting the machine to the gate, check the sliding, following the entire length, as shown in the figure below. - Page 6 4th Step: Pre-align the operator to the gate, positioning the rack over the gear and 2nd Step: The dimensions of the base must be appropriate for the dimensions of leaning the set against the gate. Then mark the fixing holes in the floor or concrete the operator.
- Page 7 6th Step: With the operator unlocked, position the rack bar over the gear and 8th Step: If the gate leaf is warped, provide wedges to ensure rack alignment. aligned with the gate. There are cases where the rack will need to extend the length of the leaf. In this It is necessary to leave approximately a 2mm gap between the top of the gear case, provide a french hand so that you don’t jump your teeth when starting the tooth and the bottom of the rack tooth.
-
Page 8: Analog Limit Swich Installation
ANALOG LIMIT SWITCH INSTALLATION 2nd Step: Fully open the gate and place the other magnet support on the rack, facing the operator’s REED. This magnet will act as the opening limit switch. 1st Step: With the gate closed, place the magnet support on the rack, positioned facing the operator’s REED. - Page 9 Once this is Technology: Voltage: done, consult the manual board which Board: Size: is available for download at www.ppa. Mounting: Fairing: com.br and perform all connections Gear: and settings. MAINTENANCE In the table below, some PROBLEMS will be mentioned —...
Need help?
Do you have a question about the DZ RIO and is the answer not in the manual?
Questions and answers