Package Contains - Stanley SCD121 Manual

PACKAGE CONTAINS

The package contains:
1 Drill/driver
1 Charger
2 Batteries (S2) or 1 Battery (S1)
1 Instruction manual
• Check for damage to the tool, parts or accessories
which may have occurred during transport.
• Take the time to thoroughly read and understand this
manual prior to operation.
FEATURES (FIG A)
This appliance includes some or all of the following features.
1. Trigger switch
2. Forward/reverse button
3. Torque adjustment collar
4 Gear shifter
5. Keyless chuck
6. Battery release button
7. Battery pack
8. LED worklight
ASSEMBLY
WARNING! Before assembly, remove the battery
from the tool.
Charging procedure (Fig. B)
• Plug the charger (10) into an appropriate outlet before
inserting battery pack.
• Insert the battery pack (7) into the charger. The charging
light will blink continuously indicating that the charging
process has started.
• The completion of charge will be indicated by the
charging light remaining ON continuously. The pack is
fully charged and may be used at this time or left in the
charger.
NOTE: To ensure maximum performance and life of Li-Ion
batteries, charge the battery pack fully before first use.
Charging Process
Refer the tables below for the state of charge of the battery
pack.
State of charge
charging
fully charged
hot/cold battery
damaged batter y
Hot/Cold pack delay
The SC122 charger have a hot/cold delay feature. When
the charger detects a battery that is hot, it automatically
delays charging until the battery has cooled. When the
charger detects a battery that is cold, it automatically delays
charging until the battery has warmed. The red light will
continue to blink and can't start to charging procedure. once
the battery has cooled, the charger will resume the charging
procedure.
Damaged battery
The charger can detect a weak or damaged battery. The
red LED flashes in the pattern indicated on the label. If you
see this damaged battery blink pattern, do not continue
to charge the battery. Return it to a service center or a
collection site for recycling.
Electronic protection system
STANLEY Li-Ion batteries are designed with an Electronic
Protection System that will protect the battery against
overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the Li-Ion battery on
the charger until it is fully charged.
Important safety instructions for all battery packs
When ordering replacement battery packs, be sure to
include catalog number and voltage.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the safety
instructions below. Then follow charging procedures
outlined.
Read all instructions
• Do not charge or use battery in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the
battery from the charger may ignite the dust or fumes.
• Never force battery pack into charger. Do not
modify battery pack in any way to fit into a non-
compatible charger as battery pack may rupture
causing serious personal injury.
• Charge the battery packs only in STANLEY chargers.
DO NOT splash or immerse in water or other liquids.
•
• Do not store or use the tool and battery pack in
locations where the temperature may reach or
exceed 40 ˚C (105 ˚F) (such as outside sheds or
metal buildings in summer).
Do not crush, drop or damage battery pack. Do not use
SC122
a battery pack or charger that has received a sharp blow,
green blink
been dropped, run over or damaged in any way (i.e.,
pierced with a nail, hit with a hammer, stepped on). Electric
green light
shock or electrocution may result. Damaged battery packs
red blink should be returned to service centre for recycling.
red flash
battery packs will stand upright on the battery pack but may
be easily knocked over.
Specific safety instructions for lithium ion (LI-Ion)
• Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
(
Original Instructions)
WARNING: Never attempt to open the battery
pack for any reason. If battery pack case is
cracked or damaged, do not insert into charger.
CAUTION: When not in use, place tool on its
side on a stable surface where it will not cause
a tripping or falling hazard. Some tools with large
ENGLISH
7