Package Contains - Stanley SCH121 Manual

ENGLISH (
Original Instructions)
CAUTION: Burn hazard. To reduce the risk
of injury, charge only STANLEY rechargeable
batteries. Other types of batteries may burst
causing personal injury and damage.
CAUTION: Children should be supervised to
ensure that they do not play with the appliance.
NOTICE: Under certain conditions, with the charger plugged
in to the power supply, the charger can be shorted by foreign
material. Foreign materials of a conductive nature such as,
but not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles should be
kept away from charger cavities. Always unplug the charger
from the power supply when there is no battery pack in the
cavity. Unplug charger before attempting to clean.
• DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The
charger and battery pack are specifically designed to
work together.
• These chargers are not intended for any uses other
than charging STANLEY rechargeable batteries. Any
other uses may result in risk of fire, electric shock or
electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when disconnecting
charger. This will reduce risk of damage to electric plug
and cord.
• Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
• Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result
in risk of fire, electric shock, or electrocution.
• Do not place any object on top of charger or place
the charger on a soft surface that might block the
ventilation slots and result in excessive internal
heat. Place the charger in a position away from any
heat source. The charger is ventilated through slots in
the top and the bottom of the housing.
• Do not operate charger with damaged cord or plug
— have them replaced immediately.
• Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way. Take it to an authorised service centre.
• Do not disassemble charger; take it to an authorised
service centre when service or repair is required.
Incorrect reassembly may result in a risk of electric
shock, electrocution or fire.
• In case of damaged power supply cord the supply cord
must be replaced immediately by the manufacturer, its
service agent or similar qualified person to prevent any
hazard.
• Disconnect the charger from the outlet before
attempting any cleaning. This will reduce the risk
of electric shock. Removing the battery pack will not
reduce this risk.
• NEVER attempt to connect 2 chargers together.
• The charger is designed to operate on standard
household electrical power. Do not attempt to use
it on any other voltage. This does not apply to the
vehicular charger.
6
Charger
The SC122 charger accept 12V Max / 10.8V Li- Ion
batteries. The charger require no adjustment and are
designed to be as easy as possible to operate.
LABELS ON TOOL
The following symbols are shown on the tool along with the
date code:
WARNING! To reduce the risk of injury, the user
must read the instruction manual.
Always wear safety goggles
Always wear safety hearing protection
Position of date code
The Date Code, which also includes the year of manufacture,
is printed into the housing.
Example:
2017 XX JN
Year of manufacturing

PACKAGE CONTAINS

The package contains:
1 Hammer drill
1 Charger
2 Batteries (S2) or 1 Battery (S1)
1 Instruction manual
NOTE: Battery packs and chargers are not included with
N-models.
• Check for damage to the tool, parts or accessories
which may have occurred during transport.
• Take the time to thoroughly read and understand this
manual prior to operation.
FEATURES (FIG. A)
This appliance includes some or all of the following features.
1. Variable speed trigger switch
2. Forward/reverse button
3. Torque adjustment collar
4. Gear shifter
5. Keyless chuck
6. Battery release button
7. Battery pack
8. LED work light
9. Function collar
ASSEMBLY
WARNING! Before assembly, remove the battery
from the tool.
Charging procedure (Fig. B)
• Plug the charger (10) into an appropriate outlet before
inserting battery pack.
• Insert the battery pack (7) into the charger. The charging
light will blink continuously indicating that the charging
process has started.