Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Xtracycle STOKER
Summary of Contents for Xtracycle STOKER
- Page 1 Manual...
-
Page 2: Tools Needed
Shimano key. The serial number is directly beneath the bar code next to "Frame No:". For the Stoker, this will start with STK. The key number is the directly beneath the bar code... - Page 3 Open the box. Inspect the contents and again look for any signs of shipping damage. Remove and set aside the small parts box, the KickBack 3 Cut the string attaching the rear of the bike to the end of and the seat with post. the box.
-
Page 4: Charge The Battery
With a friend, lift the bike out of the box and set it on your Remove the zip-ties holding the front wheel to the frame and work surface. set it aside. 10 - Charge the battery Remove the battery keys secured to the handlebars. Unlock your battery and remove it by rotating it away from the bike. - Page 5 Find the battery charger and domestic power cable in the Make sure the charge indicator lights begin to blink green. small parts box. Locate the charging port on the drive side A full charge will take a few hours but you will be able to use of the battery.
- Page 6 Rest the back of the kickstand mounting plate on the Install the first U-bolt on the drive side of the bike. Fit an mounting shelf and use a 3 mm Allen wrench to thread the M6 washer and nut onto the forward threads, until just M5 set screw in order to hold the kickstand in place.
-
Page 7: Install The Front Wheel
20 - Install the front wheel Carefully lift the front of the bike and deploy the kickstand. Remove the packaging around the fork and fender. Remove the thru-axel with a 6 mm Allen wrench. Remove the disc brake-pad spacer. Remove the packaging from the front wheel. - Page 8 Rotate your front wheel into position. Be mindful to seat the Re-insert your thru-axel, and tighten with a 6 mm disc brake rotor neatly between the brake pads. Allen wrench. 26 - Adjust the front light Use a 4 mm Allen wrench to loosen the bolt on the fender tab Loosen the two pivot bolts to adjust the angle of the light, as and rotate the light into a vertical position.
-
Page 9: Install The Pedals
28 - Install the pedals Apply a small amount of grease to the threads on each pedal, With the right pedal, start threading the pedal bolt into the marked Left and Right. crank arm. Once initially threaded you can backpedal while holding the pedal bolt in place. -
Page 10: Adjust Handlebars
32 - Adjust handlebars Remove the rubber plug on the top-cap, and use a 5 mm Align your handlebars with your front wheel. Allen wrench to loosen the bolt. Re-tighten the two stem bolts, and the top-cap bolt and Use a 4 mm Allen wrench to loosen the two bolts holding replace the rubber plug. - Page 11 Use the provided Shimano lead-connector tool from the Replace your battery by sliding it into the cradle and rotating small parts box to insert the display cable into the small port towards the bike frame until it clicks into place. under the display.
- Page 12 If you would like to switch the width setting on your U-Tubes to narrow or wide: The U-tubes should easily slide into the mounting holes. Press the spring pin button in and push or pull the spring But it is possible an adjustment will be needed if the fit the pin elbow on the inside of the U-Tube until the button pops alignment is not perfect.
- Page 13 Push or pull the tailpiece into a place where you can easily Insert the U-tube into the frame, pushing in on the spring pin insert the U-tube. button so that the button slides into the frame as well. Insert the U-tube far enough for the spring pin to pop out into the Do not tighten the tailpiece yet.
-
Page 14: Complete Assembly
47 - Complete assembly Tie down the two hook and loop straps on the bottom of the The Stoker assembly is complete and you are ready to ride! FreeLoader Too bags to the bike frame. Looking to install additional accessories...