Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Xtracycle RFA
Summary of Contents for Xtracycle RFA
- Page 1 RFA assembly Manual...
-
Page 2: Tools Needed
Shimano key. The serial number is directly beneath the bar code next to "Frame No:". For the RFA, this will start with RFA. The key number is the directly beneath the bar code next to... - Page 3 Inspect the contents and again look for any signs of shipping damage. Remove and set aside the small parts box, the RFA KickBack Cut the string attaching the rear of the bike to the end of and the seat with post.
-
Page 4: Charge The Battery
With a friend, lift the bike out of the box and set it on your Remove the zip-ties holding the front wheel to the frame and work surface. set it aside. 10 - Charge the battery Remove the battery keys secured to the handlebars. Unlock your battery and remove it by rotating it away from the bike. - Page 5 Also note that the battery will not supply power while it is charging. 14 - Install the RFA KickBack Bring the KickBack up and under the RFA. The mounting Place the KickBack so that the 2 ovalized holes on each side plate should be placed inside the two horizontal chainstays.
- Page 6 Place two washers on one of the M8 bolts. Starting on the It is important to start this off with just your fingers to help inside of the mounting plate and using just your fingers, insure that you do not cross thread the bolt since you may be thread the bolt with the washers to the front boss until you coming at it from an off angle.
-
Page 7: Install The Front Wheel
Using the ball or short end of the Allen wrench, tighten the Using the shorter end of the Allen wrench, tightly secure all two rear bolts. bolts in place. 22 - Install the front wheel Carefully lift the front of the bike and deploy the kickstand. Remove the packaging around the fork and fender. - Page 8 Remove the disc brake-pad spacer. Remove the packaging from the front wheel. Rotate your front wheel into position. Be mindful to seat the Re-insert your thru-axel, and tighten with a 6 mm disc brake rotor neatly between the brake pads. Allen wrench.
-
Page 9: Install The Pedals
28 - Adjust the front light Use a 4 mm Allen wrench to loosen the bolt on the fender tab Loosen the two pivot bolts to adjust the angle of the light, as and rotate the light into a vertical position. needed. -
Page 10: Install The Seat
32 - Install the seat Apply a modest amount of grease to the inside of the Lower your seatpost into your desired position and tighten seat tube. the collar with a 5 mm Allen wrench. 34 - Adjust handlebars Remove the rubber plug on the top-cap, and use a 5 mm Align your handlebars with your front wheel. - Page 11 Use a 4 mm Allen to loosen the faceplate on the front of your Use a 3 mm Allen wrench to loosen the paddle grips. stem, and center the positioning target. Then retighten Reposition them so they are level with the ground. Then the faceplate.
- Page 12 40 - Install the RFA FootRests Pick the RFA FootRest that corresponds to the side of the Using a 4 mm Allen wrench, remove the top of the clamp bike you are installing it on first. The flat plate is installed located on the back end of the FootRest.
- Page 13 Position the FootRest on the bike and loosely thread the two Attach the top portion of the rear clamp over the bottom 8 mm bolts through the front mounting plate and into the rail of the UtilityRack. Loosely thread two 4 mm bolts with threads on the frame.
- Page 14 Re-tighten the bolts securing the UtilityRack to the frame. Reattach the RFA WheelSkirts. The RFA assembly is complete and you are ready to ride! Looking to install additional accessories on your RFA? Please refer to the following page on the Xtracycle wesbite for links to additional installation manuals: https://www.xtracycle.com/product-manuals...