Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Xtracycle SWOOP
Summary of Contents for Xtracycle SWOOP
- Page 1 Swoop assembly Manual...
-
Page 2: Tools Needed
Shimano key. The serial number is the number under the bar code next to "Frame No:". For the Swoop, this will start with SWP (the barcode show here is for a Stoker). The key number... - Page 3 Open the box. Inspect the contents and look again for any signs of shipping damage. Remove and set aside the small parts box, the KickBack 3 Cut the string attaching the rear of the bike to the end of and the seat with post. the box.
-
Page 4: Charge The Battery
With a friend, lift the bike out of the box and set it on your Remove the zip-ties holding the front wheel to the frame and work surface. set it aside. 10 - Charge the battery Remove the battery keys secured to the handlebars. Unlock your battery and remove it by rotating it away from the bike. - Page 5 Find the battery charger and domestic power cable in the Make sure the charge indicator lights begin to blink green. small parts box. Locate the charging port on the drive side A full charge will take a few hours but you will be able to use of the battery.
- Page 6 Rest the back of the kickstand mounting plate on the Install the first U-bolt on the drive side of the bike. Fit an mounting shelf and use a 3 mm Allen wrench to thread the M6 washer and nut onto the forward threads, until just M5 set screw in order to hold the kickstand in place.
- Page 7 20 - Install the front fender & wheel Carefully lift the front of the bike and deploy the kickstand. Remove the packaging around the fork and fender. Remove the thru-axel with a 6 mm Allen wrench. From the smal-parts box, locate the fender mount L-bracket, Insert the M6 x 50 mm bolt and one M6 washer in the upper M6 x 50 mm bolt, two M6 washers, M6 nyloc nut and two fork hole.
- Page 8 Bring the front fender into position by hanging the mounting Usa a 4 mm Allen wrench to attach the outer support arms tab from the M6 x 50 mm bolt and holding it in place with of the fender to the lower fork-mounting points with the two the L-bracket, M6 washer &...
- Page 9 Rotate your front wheel into position. Be mindful to seat the Re-insert your thru-axel, and tighten with a 6 mm disc brake rotor neatly between the brake pads. Allen wrench. 31 - Mount the front light Returning to the fender, tighten the upper bolt with a 4 mm The fender-mounted headlight is secured with an M6 nut, M6 Allen wrench and an 8 mm socket tool.
- Page 10 Place the flat washer over the M6 bolt and insert the bolt Use a 5 mm Allen wrench to thread the bolt into the nut through the light mounting tab on the fender. through the light mounting arm. Then place the spider washer on the bolt. Connect the fender headlight leads by matching black to Connect the leads at the top of the fork by matching black to black and red to black-with-gray stripe.
- Page 11 36 - Set up the handlebars Use a 4 mm Allen wrench to loosen the two bolts holding Remove the rubber plug on your top-cap and use a 5 mm your handlebar stem in place. Allen wrench to remove the bolt and top-cap. Remove the spacers and the handlebar stem.
- Page 12 Replace the top-cap and bolt and tighten with the 5 mm Align your handlebars with your front wheel and re-tighten Allen wrench. the two stem bolts. Replace the rubber plug. Use a 4 mm Allen wrench to loosen the faceplate on the front Use a 3 mm Allen wrench to loosen the paddle grips.
-
Page 13: Install The Pedals
44 - Install the pedals Apply a small amount of grease to the threads on each pedal, With the right pedal, start threading the pedal bolt into the marked Left and Right. crank arm. Once initially threaded you can backpedal while holding the pedal bolt in place. - Page 14 48 - Intsall the StabilizerSpring Locate the following hardware in the small parts box: eyebolt, Fully thread the eye-bolt through the flange nut. flange nut, StabilizerSpring, and spring sleeve. Thread the bolt through the threaded boss on the downtube. Hook the StabilizerSpring to the L-bracket on the fork. Tighten with a 8 mm wrench, adjusting the eye bolt so it is aligned perpendicular to the bike.
- Page 15 Use an Allen wrench or screwdriver to pull the other end Slide the spring sleeve over the StabilizerSpring. through the eye-bolt. Push up on the spring to fully seat the StabilizerSpring. 54 - Install the U-Tubes Before installing the U-Tubes, please note that the rear Determine if you would like to have the U-tubes installed in insertion end on each U-Tube is slightly longer than the the wide setting (shown on the left side of the bike pictured...
- Page 16 If you would like to switch the width setting on your U-Tubes to narrow or wide: The U-tubes should easily slide into the mounting holes. Press the spring pin button in and push or pull the spring But it is possible an adjustment will be needed if the fit the pin elbow on the inside of the U-Tube until the button pops alignment is not perfect.
- Page 17 Push or pull the tailpiece into a place to where you can easily Insert the U-tube into the frame, pushing in on the spring pin insert the U-tube. button so that the button slides into the frame as well. Insert the U-tube far enough for the spring pin to pop out into the Do not tighten the tailpiece yet.
-
Page 18: Complete The Assembly
63 - Complete the assembly Tie down the two hook & loop straps on the bottom of the Wrap the cable-protecting covers over the headlight wires. FreeLoader Too bags to the bike frame. Use the Shimano lead-connector tool from the small parts Replace your battery by rotating it back into place from the box to insert the display cable into the small port under the front of the bike until it clicks into place. - Page 19 Looking to install additional accessories? 67 - Complete the assembly Please refer to the following page on the Xtracycle Congratulations, your Swoop assembly is complete and you wesbite for links to additional installation manuals: are now ready to ride! https://www.xtracycle.com/product-manuals...