Advertisement
Quick Links
Advertisement
Related Manuals for Xtracycle EdgeRunner Swoop
Summary of Contents for Xtracycle EdgeRunner Swoop
- Page 1 E d g e R u n n e r S w o o p / C l a s s i c A S S E M B L Y M A N U A L Rev 1A...
- Page 2 This is important when sharing the bike between differently sized riders (i.e. families or demo bikes) and is a surprisingly effective way to customize fit on upright bikes. Warning: Always use wheel protection like WheelSkirts or Xtracycle bags when riding with passengers or cargo.
- Page 3 2. Smaller Box with Sizing Kit: Will include: an Xtracycle seatpost and a stem. May include Xtra- cycle Kickback 3, Herrmans lightset, Xtracycle bags or WheelSkirts, and other accessories you’ve...
- Page 4 Unboxing the EdgeRunner • Open the box • Fold the corner of the cardboard block closest to the • Remove the accessory box from the back of the bike. seat post back and out of the way, to make room for •...
- Page 5 Remove the Fork and Front Wheel Remove the fork from above the rear wheel - this Both the front wheel and the handlebars are attached does not require removing the deck. to the thick, protective cardboard “front wheel block.” Remove the bars first and zip tie them to the top tube to avoid damaging the hoses or derailleur cables.
- Page 6 Install the Fork Find the headset and spacers in the included small The headset includes a thin rubber seal that sits on the parts box, and the S/M/L sized stem (paired with lip of the crown race. Install this first, then the lower seatpost) in the separately-shipped accessory box.
- Page 7 Install the Headset & Stem Slide on the upper bearing, top race, split bushing, bearing cap, spacers, and the stem. Install the stem cap and bolt to hold things in place, but do not adjust at this point.
-
Page 8: Install Handlebar
Install Handlebar • Remove the faceplate with integrated light mount from the stem, and install the handlebars so that the ends of the bars will lie parallel to the ground. Torque the stem faceplate bolts to 6nM. • Angle the shifter/brake lever down 45 degrees. - Page 9 Bolt Brakes to Fork The front brake and its bolts are attached to the handlebars - bolt the brake to the fork per the included shimano instructions, but do not torque it down yet. Install the Rotor The 180mm front rotor is in the accessory box - at- tach it to the front wheel, this requires a 16-notch...
-
Page 10: Adjust The Derailleurs
Adjust the Rear Brake Adjust the Derailleurs Pro tip: If you are installing U-Tubes, now is a good time to do it - refer to the U-Tube documentation, found on the Xtracycle Support page, for details. - Page 11 Check RackLocks & V-Racks Make sure the RackLocks and V-Racks are seated correctly: The racks should be fully inserted into the uprights and the Rack- Locks should be pushed all the way down on the uprights and the outer clamp should fully cover the inner collar.
- Page 12 *Pro Tip: If you are installing bags, the V-Racks. WheelSkirts are not necessary. This is the right time to install Xtracycle bags.
- Page 13 Bolt Down the Deck If you’ve already installed your Hooptie handrails (optional) secure the deck by tightening the four bolts already in the deck and installing the four long bolts and nylock nuts provided into the empty bosses on the V-Rack - two in the front and two in the rear. Note: The larger thicker washer goes between the deck and the V-Rack.
- Page 14 Adjust the WeddingRings Finally, apply some blue loctite to the threads of the WeddingRings, and tighten them to a more harmonious union - take out the slack, then add a full turn for ten- sion. Install Handlebar Stabilizer Use pliers to thread the spring. Install protective cover over stabilizer spring.
- Page 15 KickBack Installation Refer to Kickback instructional manual. Install The Front Light (Skip to step 21 if your model didn’t come with a front light) Remove the black nut and bolt holding the light to its bracket. Note that the nut will fit into a hexagonal pocket on one side of the bracket, so you won’t need to hold it by hand/wrench.
- Page 16 Install the Front Light Cont’d Attach the bracket to the mounting eyelets on the stem using the shorter silver bolt and match- ing nut. The semi-spherical washers should go on either side of the eyelets, pointing inwards. This bolt should be tightened enough that the light will stay in place if the front end of the bike is bounced on the ground.