Table of Contents
Advertisement
ASSEMBLY
Warning Lamp Installation, 12FT
NOTE
12FT 3-PT model is shown, drawbar model similar.
1. Place a Red Lamp at each end of the Light Bar and
insert the Red Lamp cord into the Light Bar cutout.
Secure Red Lamps to Light Bar with 1/4-20 x 1-1/4
Bolts and Locknuts. See Figure 2-17.
2. Attach longer Light Bracket to the Transmission
located on the left side of the Seeder, with 3/8-16 x
1-1/2 Bolts, Lock Washers and Nuts.
3. Attach an Amber Lamp to the upper portion of the
longer Light Bracket with 1/4-20 x 1-1/4 Bolts and
Locknuts.
4. On the right side of the Seeder attach the shorter
Light Bracket to the Angle Bracket with 1/2-13 x 1-1/4
Bolts, Lock Washers and Nuts.
5. Attach an Amber Lamp to the upper portion of the
Light Bracket with 1/4-20 x 1-1/4 Bolts and Locknuts.
6. Attach the Flasher Control Module to the Module
Bracket with 1/4-20 x 1-1/2 Bolts and Locknuts. See
Figure 2-16.
IMPORTANT
Cords are marked Yellow Tape for Left and Green
Tape for Right.
7. Lay out the Lamp Harness along the Seeder Frame
Tube, Cords with Yellow Tape Left and Cords with
Green Tape Right. Connect the Harness to the
Flasher Control Module 6-Prong Connector.
8. Route the left and right cords along the front of the
Frame Tube. Route the 3-Prong Connector Cords
into the Light Bar vertical tube openings up to the
Red Lamps and connect. Continue routing the
2-Prong Connector Cord along the front of the frame,
up the outer Light Bracket to the Amber Lamps and
connect.
9. Lay out the 7-Pin Harness along the 3-PT Hitch or
Drawbar with the 4-Prong Connector towards
Seeder. 3-PT Hitch, route the 4-Prong Connector
Cord through the Frame Loop to the Module.
Drawbar, route the 7-Pin Harness along the
Drawbar, through the Hose Support up to the
Tractor. Connect 7-Pin Harness 4-Prong Connector
to the Flasher Control Module.
10. Bundle and secure excess Cords to the Module
Bracket with Tie Wraps. Along the Seeder Frame,
secure Harness Cords with Tie Wraps to the frame
end plate slots, Slotted Tabs and Hydraulic Hoses.
Bundle and secure 7-Pin Harness to the Drawbar
Hydraulic Hoses or 3-PT Hitch Frame Slots allowing
enough Harness length to reach the Tractor Socket.
2-12
NOTE
If equipped with Electrical Clutch, install, route and
secure Electric Clutch Harness with the Warning Lamp
Harness.
IMPORTANT
All Harnesses must be firmly attached to Machine
Frame members or Hydraulic Hoses so they do not
sag or become torn loose by field debris.
11. Attach the SMV sign to the SMV Mount located on
the center of the Light Bar with 5/16-18 x 1 Bolts, Flat
Washers, and Locknuts.
12. Attach the Connector Holder to the 3-PT Hitch or
Drawbar Hose Holder with 1/4-20 x 1 Bolts, Flat
Washers, and Locknuts.
NOTE
The 7-Pin plug on the other end of the 7-Pin Harness
connects to the Tractor Socket when in use. When not in
use, it can be stored in the Connector Holder on the 3-PT
Hitch or Drawbar Hose Holder. Allow enough Harness
length to reach Tractor Socket and roll or fold up excess
and secure to Drawbar Hydraulic Hoses or 3-PT Hitch.
Bolt,
1/4-20 x 1-1/2
Flasher Control Module
Figure 2-16: Flasher Control Module and Bracket
Module Bracket
Locknut,1/4-20
1P480-0522
Advertisement
Table of Contents
