Summary of Contents for Advantech IDK-2110R XGA Series
Page 1
User Manual IDK-2110R XGA Series TFT-LCD 10.4" XGA (LED Backlight)
Page 2
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
Page 3
Whether your new Advantech equipment is destined for the labo- ratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known.
Page 4
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
General Description This user manual is for the 10.4 inch color TFT LCD module IDK-2110R XGA-series. IDK-2110R XGA is designed with a wide viewing angle, wide operating temperature and long life LED backlight which is well suited for Industrial Applications. The LED driving board for the backlight unit is included in this panel and the LED units are replaceable.
Mechanical Dimension AA Center 2-M3 USER HOLE 2-M3 USER HOLE MIN. DEPTH 3.9mm MIN. DEPTH 3.9mm MAX. TORQUE 0.35N-m MAX. TORQUE 0.35N-m Unit: mm Absolute Maximum Ratings 1.5.1 Absolute Ratings of the TFT LCD Module Value Item Symbol Unit Conditions Min.
TFT LCD Module 2.1.1 Electrical characteristics\ Value Parameter Symbol Unit Condition Min. Typ. Max. Supply voltage Current consumption Permissive input mVp-p =3.3V ripple voltage 0.3V "Low" level Input signal voltage 0.7V "High" level μA Input leak current μA =3.3V LVDS Input voltage Differential input voltage...
Backlight Unit 2.2.1 Parameter guideline for LED backlight The following characteristics are measured under stable conditions using an inverter at 25°C (Room Temperature): Value Parameter Symbol Unit Remark Min. Typ. Max. Input Voltage 10.8 13.2 [Volt] Input Current 1120 [mA] 100% PWM Duty Power Consumption 10.44...
Pixel Format Image The following figure shows the relationship between the input signal and LCD pixel format. Pin Description LVDS is a differential signal technology for LCD interface and high speed data trans- fer devices. The connector pin definition is as below. Note “Low”...
Page 20
Note1 Please follow PSWG. Note2 R/G/B data 7:MSB, R/G/B data 0:LSB Signal Name Description Remark Red Data 7 Red Data 6 Red-pixel Data Red Data 5 For 8 bits LVDS input, Red Data 4 MSB: R7; LSB:R0 Red Data 3 Red Data 2 For 6 bits LVDS input, MSB: R5;...
Note: Output signals from any system shall be low or Hi-Z state when VDD is off. Interface Timing 3.4.1 Timing Characteristics DE mode only Table 3.2: Timing Characteristics Parameter Symbol Min. Typ. Max. Unit Condition Clock frequency 1/ T Clock Period Vertical Active...
Power ON/OFF Sequence VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system will be Hi-Z state or low level when VDD is off. Power Sequence Timing Parameter Value Unit Min.
TFT LCD Signal(CN1): LVDS Connector Table 4.1: Connector Connector Name / Description Signal Connector Manufacturer I-PEX or compatible Connector Model Number 20186-020E-11F or Compatible Adaptable Plug 20197-020U-F, 20197-T20U-F or compatible Table 4.2: Pin Assignment Pin No. Signal Name Pin No. Signal Name RxIN0- RxIN0+...
Touch Characteristics This touch panel is a resistance type that customers use with flat displays like LCDs. Once an operator touches it with a stylus or finger, the circuit sends coordinate points to the PC in voltages from the contact point. Optical Characteristics Item Specification...
Touch Controller Characteristics Advantech ETM-RES05C Touch Control Board is the ultimate combo board. This touch panel controller provides optimum performance for your analog resistive touch 4-wire model panels. It communicates with the PC directly through USB and RS-232 connectors. You can see how superior the design is through its sensitivity accuracy and friendly operation.
Relative Humidity 95% at 60°C, RH Non-condensing Acquired RoHS certificate Requlatory FCC-B, CE approvals Dimension: 75 mm x 20 mm x 10 mm Pin Assignment and Description 6.4.1 Connector and LED Location 6.4.2 Combo Interface Connector, JP1, Pins Signal Descriptions The combo interface connector, USB and RS-232, is a box 2.0mm 10-pins 90 degree, Male type with lock connector, intended to be used with single wired pins in...
6.4.3 Touch Screen Connector, JP2, Pins and Signal Descriptions The Touch Screen connector, JP2, is a FFC/FPC SMD 1.0mm 4-pins 90 degree, Female type connector. The pins are numbered as shown in the table below. TS4 Pin # Signal Name Signal Description Bottom Left...
Optical Characteristics The optical characteristics are measured under stable conditions at 25°C (Room Temperature): Item Conditions Min. Typ. Max. Unit Note White IF= 50mA 1300 [cd/m2] Luminance (center point) Uniformity 9 Points 1, 2, 3 Contrast Ratio Response Time Rising [msec] Falling [msec]...
Page 33
Note4 Definition of Luminance Uniformity: Measured Maximum luminance [L(MAX)] and Minimum luminance [L(MIN)] on the 9 points Luminance Uniformity is calculated with the following formula: L =[ L(MIN) / L (MAX) ] X 100% Note5 Definition of Viewing Angle IDK-2110R XGA User Manual...
Handling Precautions The optical characteristics are measured under stable conditions at 25°C (Room Temperature) Since the front polarizer is easily damaged, pay attention not to scratch it. Be sure to turn off power supply when inserting or disconnecting from input con- nector.