Specific Safety Instructions - stayer TV509D Operating Instructions Manual

The machine TV509D is intended for stationary use
with cutting abrasive discs to perform lengthways and
crossways straight cuts or mitre cuts to 45° in metal
materials without the use of water.
This manual is consistent with the date of manufacture of
your machine, you will find information on the technical
data of the machine acquired manual check for updates
of our machines on the website: www.grupostayer.com

Specific safety instructions

Never stand on the power tool. Serious injuries could
occur when the power tool tips over or when accidentally
coming into contact with the cutting disc.
Always use the blade guard. A blade guard protects
the user against broken off parts of the cutting disc and
against accidental touching of the cutting disc.
Make sure that the guard operates properly and that
it can move freely. Never lock the guard in place when
opened.
Use the power tool only for dry cutting. Water
penetrating into a power tool increases the risk of an
electric shock.
Keep the mains cable away from rotating application
tools. The mains cable can be cut through or get caught.
Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing loss of
control.
Never remove cutting remainders, metal chips, etc.
from the cutting area while the machine is running.
Always guide the tool arm back to the neutral position
first and then switch the machine off.
Guide the cutting disc against the workpiece only
when the machine is switched on. Otherwise, there
is danger of kickback, when the cutting disc becomes
wedged in the workpiece.
Only approaching the cutting disc running against
the workpiece when the disc reaches its maximum
speed. After starting wait at least 4 seconds until the disk
rotate at rated speed.
Always firmly clamp the workpiece. Do not cut
workpieces that are too small to clamp. Otherwise, the
clearance of your hand to the rotating cutting disc is too
small.
If the cutting disc becomes jammed, switch the
machine off and wait until the cutting disc comes to
a complete stop. Never attempt to remove a still running
cutting disc from the cut, otherwise there is danger
of kickback. Determine and correct the cause for the
jamming.
After switching off, do not stop the cutting disc by
applying lateral pressure to it. The cutting disc can
become damaged, break or lead to kickback.
ENGLISH
18
Do not force the cutting disc into the workpiece and
do not apply too much pressure when using the
power tool. Particularly avoid jamming or wedging the
cutting disc when working corners or sharp edges. When
the cutting disc is damaged due to abuse, cracks can
form that can lead to breakage without prior warning.
Wear a work apron. Pay attention that other persons
are not put at risk from sparking. Remove flammable
materials in close vicinity. Sparking occurs when cutting
metal.
Use the cut off grinder only for cutting materials
mentioned under "Intended Use". Otherwise, the cut
off grinder can be subject to overload.
Do not use damaged, out-of-centre or vibrating
cutting discs. Damaged cutting discs cause increased
friction, binding of the cutting disc and kickback.
Always use cutting discs with correct size and shape
(diamond versus round) of arbor holes. Cutting discs
that do not match the mounting hardware of the cut off
grinder will run eccentrically, causing loss of control.
Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control over the power tool.
Observe the operating instructions of the cut-off
wheel manufacturer for assembly and use of the cut-
off wheel. Cut-off wheels that do not fit can lead to injury
as well as to jamming, breaking or kickback.
Do not use accessories which are not specifically
designed and
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
Do not touch the cutting disc after working before
it has cooled. The cutting disc becomes very hot while
working.
Check the cable regularly and have a damaged cable
repaired only through an authorised customer
service agent for STAYER power tools. Replace
damaged extension cables. This will ensure that the
safety of the power tool is maintained.
Store the machine in a safe manner when not being
used. The storage location must be dry and lockable.
This prevents the machine from storage damage, and
from being operated by untrained persons.
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
Never leave the machine before it has come to a
complete stop. Cutting tools that are still running can
cause injuries.
18
recommended by the tool