Banner WORLD-BEAM QS30LLP Series Quick Start Manual

Banner WORLD-BEAM QS30LLP Series Quick Start Manual

Polarized retroreflective laser sensors
Hide thumbs Also See for WORLD-BEAM QS30LLP Series:

Advertisement

Quick Links

WORLD-BEAM QS30 LLP and LLPC
Polarized Retroreflective Laser Sensors
Excellent for applications where high sensing power and small beam size are important. Operates over sensing ranges typically accom-
plished only by conventional opposed-mode photoelectrics; uses a special filter to polarize the emitted light, filtering out unwanted reflec-
tions from shiny objects.
Models
Model
Range and Use
QS30LLP
0.2 to 18 m (0.67' to 60')
Maximum Excess Gain SET
for Long-Range Applications
QS30LLPQ
QS30LLPC
0.2 to 18 m (0.67' to 60')
Low-Contrast SET for Small
Object Detection
QS30LLPCQ
* 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g., QS30LLP W/30). A model with a
QD connector requires a mating cable (see
WARNING: Not To Be Used for Personnel Protection
Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury
or death. This product does NOT include the self-checking redundant circuitry necessary to allow its use in
personnel safety applications. A sensor failure or malfunction can cause either an energized or de-ener-
gized sensor output condition.
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
• Visible class 1 laser with small, effective beam size
• Excellent optical performance throughout sensing range, even close up
• Easy push-button SET options: Maximum Excess Gain or Low-Contrast
SET, depending on model, plus Manual Adjust
• Easy-to-read operating status indicators, with 8-segment bargraph display
• Bipolar discrete outputs, PNP and NPN
• Selectable 30 millisecond OFF-delay
• Models available with 2 m or 9 m (6.5' or 30') cable or integral quick-discon-
nect
• Tough ABS housing rated IEC IP67; NEMA 6
• Compact housing, mounting versatility – popular 30 mm threaded nose or
side-mount
Spot Size at Fo-
cus
Approx. 4 mm at
10 m (0.16" at 33')
Quick-Disconnect Cables
on page 9).
Features
Cable*
Supply
2 m (6.5') 5-wire Ca-
ble
Integral 5-pin Euro-
style QD
10 to 30V dc
2 m (6.5') 5-wire Ca-
ble
Integral 5-pin Euro-
style QD
Output Type
Bipolar NPN /
PNP

Advertisement

Table of Contents
loading

Summary of Contents for Banner WORLD-BEAM QS30LLP Series

  • Page 1 WORLD-BEAM QS30 LLP and LLPC Polarized Retroreflective Laser Sensors Features • Visible class 1 laser with small, effective beam size • Excellent optical performance throughout sensing range, even close up • Easy push-button SET options: Maximum Excess Gain or Low-Contrast SET, depending on model, plus Manual Adjust •...
  • Page 2: Sensor Configuration

    WORLD-BEAM QS30 LLP and LLPC Excess Gain With Supplied Target BRT-51X51BM With Supplied Target BRT-THVG-2X2 With Target BRT-2X2 (Optional) 1000 1000 1000 with BRT-51X51BM with BRT-TVHG2X2 with BRT-2X2 0.1 m 1.0 m 10 m 100 m 0.1 m 1.0 m 10 m 100 m 0.1 m...
  • Page 3 WORLD-BEAM QS30 LLP and LLPC Push Button Disable In addition to its programming function, Remote Programming may be used to disable the push buttons for security. Disabling the push buttons prevents undesired tampering with the programming settings. Connect the gray wire of the sensor as described on above, and four-pulse to either enable or disable the push buttons: Maximum Excess Gain SET - Model QS30LLP •...
  • Page 4 WORLD-BEAM QS30 LLP and LLPC Low-Contrast SET - Model QS30LLPC Location of switchpoint • Sets a switchpoint at 35 percent below the signal from the retroreflector. adjusted via Manual Adjust • Useful for small object detection and other applications with small varia- 35% of tions in contrast, such as yarn- or thread-break applications.
  • Page 5: Setup Mode

    WORLD-BEAM QS30 LLP and LLPC SETUP Mode SETUP mode is accomplished via the sensor’s two push buttons. It is used to change sensor output response for: SETUP • Light or Dark Operate status indicators • 30-millisecond pulse stretcher (OFF-delay), if required. The status LEDs, active only during SETUP mode, indicate the output response configuration when the sensor will be in RUN mode.
  • Page 6: Installation Notes

    WORLD-BEAM QS30 LLP and LLPC Installation Notes Conventional retroreflective photoelectric sensors are extremely easy to align. Beam angles are wide, and retro targets are forgiving to the light beam’s angle of incidence. The beam of this laser sensor is very narrow, compared with the beam of most retro sensors. As Figure 6 indicates, the effect of angular misalignment can be dramatic.
  • Page 7: Specifications

    WORLD-BEAM QS30 LLP and LLPC Specifications Supply Voltage and Current Indicators 10 to 30V dc (10% max. ripple @ 10% duty cycle) @ Green LED: Power ON 35 mA max current, exclusive of load Yellow LED: Output conducting Sensing Beam 8-Segment Red Bargraph Visible red LED, 650 nm SETUP mode:...
  • Page 8 WORLD-BEAM QS30 LLP and LLPC Description of Laser Classes Class 1 Lasers Lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. Reference IEC 60825-1:2001, Section 8.2. For Safe Laser Use (Class 1 or Class 2): •...
  • Page 9 4=Black M12 x 1 5=Gray ø 14.5 [0.57"] Retroreflective Targets See the Accessories section of your current Banner Photoelectric Sensors catalog for complete information. NOTE: Polarized sensors require cor- ner cube type retroreflective targets only. Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com...
  • Page 10 WORLD-BEAM QS30 LLP and LLPC BRT-2X2 BRT-51X51BM • Square, acrylic target • Square, acrylic target • Reflectivity factor: 1.0 • Reflectivity Factor: 1.5 • Max. temperature: 50° C (+122º F) • Max. Temperature: +50°C (+122°F) • Optional brackets are available •...
  • Page 11: Accessory Brackets

    Warranty: Banner Engineering Corporation warrants its products to be free from defects for a period of one year. Banner Engineering Corporation will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period.

This manual is also suitable for:

World-beam qs30llpc seriesWorld-beam qs30llpWorld-beam qs30llpqWorld-beam qs30llpcWorld-beam qs30llpcq

Table of Contents