Banner QS30LLPQ Manual

Banner QS30LLPQ Manual

World-beam, polarized retroreflective laser sensors
Hide thumbs Also See for QS30LLPQ:

Advertisement

WORLD-BEAM QS30 LLP and LLPC
Polarized Retroreflective Laser Sensors
Excellent for applications where high sensing power and small beam size are important. Operates over sensing ranges typically accom-
plished only by conventional opposed-mode photoelectrics; uses a special filter to polarize the emitted light, filtering out unwanted reflec-
tions from shiny objects.
Models
Model
Range and Use
QS30LLP
0.2 to 18 m (0.67 ft to 60 ft)
Maximum Excess Gain SET
for Long-Range Applications
QS30LLPQ
QS30LLPC
0.2 to 18 m (0.67 ft to 60 ft)
Low-Contrast SET for Small
Object Detection
QS30LLPCQ
* 9 m (30 ft) cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g., QS30LLP W/30). A model with
a QD connector requires a mating cable (see
WARNING: Not To Be Used for Personnel Protection
Never use this product as a sensing device for personnel protection. Doing so could lead to serious
injury or death. This product does NOT include the self-checking redundant circuitry necessary to allow its
use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-
energized sensor output condition.
P/N 112355 Rev. C
• Visible class 1 laser with small, effective beam size
• Excellent optical performance throughout sensing range, even close up
• Easy push-button SET options: Maximum Excess Gain or Low-Contrast
SET, depending on model, plus Manual Adjust
• Easy-to-read operating status indicators, with 8-segment bargraph display
• Bipolar discrete outputs, PNP and NPN
• Selectable 30 millisecond OFF-delay
• Models available with 2 m or 9 m (6.5' or 30') cable or integral quick-discon-
nect
• Tough ABS housing rated IEC IP67; NEMA 6
• Compact housing, mounting versatility – popular 30 mm threaded nose or
side-mount
Spot Size at Fo-
cus
Approx. 4 mm at
10 m (0.16 in at 33
ft)
Quick-Disconnect Cables
on page 10).
12/18/2013
Features
Cable*
Supply
2 m (6.5 ft) 5-wire Ca-
ble
Integral 5-pin Euro-
style QD
10 to 30V dc
2 m (6.5 ft) 5-wire Ca-
ble
Integral 5-pin Euro-
style QD
Output Type
Bipolar NPN /
PNP
0 112355
5

Advertisement

Table of Contents
loading

Summary of Contents for Banner QS30LLPQ

  • Page 1 QS30LLP 0.2 to 18 m (0.67 ft to 60 ft) Maximum Excess Gain SET Integral 5-pin Euro- for Long-Range Applications QS30LLPQ Approx. 4 mm at style QD Bipolar NPN / 10 m (0.16 in at 33 10 to 30V dc 2 m (6.5 ft) 5-wire Ca-...
  • Page 2: Excess Gain

    WORLD-BEAM QS30 LLP and LLPC Excess Gain With Supplied Target BRT-51X51BM With Supplied Target BRT-TVHG-2X2 With Target BRT-2X2 (Optional) 1000 1000 1000 with BRT-51X51BM with BRT-TVHG2X2 with BRT-2X2 0.1 m 1.0 m 10 m 100 m 0.1 m 1.0 m 10 m 100 m 0.1 m...
  • Page 3: Remote Configuration

    WORLD-BEAM QS30 LLP and LLPC Remote Configuration The Remote Configuration function may be used to set the sensor threshold remotely or to disable the push buttons for security. Connect the gray wire of the sensor to ground (0V dc), with a remote programming switch connected between them. Pulse the remote line accord- ing to the diagrams in the programming procedures.
  • Page 4 WORLD-BEAM QS30 LLP and LLPC Push Button Remote Indicators (0.04 seconds < T < 0.8 seconds) — GAIN www.bannerengineering.com - tel: 763-544-3164 P/N 112355 Rev. C...
  • Page 5 WORLD-BEAM QS30 LLP and LLPC Low-Contrast SET - Model QS30LLPC Location of switchpoint • Sets a switchpoint at 35 percent below the signal from the retroreflector. adjusted via Manual Adjust • Useful for small object detection and other applications with small varia- 35% of tions in contrast, such as yarn- or thread-break applications.
  • Page 6: Setup Mode

    WORLD-BEAM QS30 LLP and LLPC SETUP Mode SETUP mode is accomplished via the sensor’s two push buttons. It is used to change sensor output response for: SETUP • Light or Dark Operate status indicators • 30-millisecond pulse stretcher (OFF-delay), if required. The status LEDs, active only during SETUP mode, indicate the output response configuration when the sensor will be in RUN mode.
  • Page 7: Installation Notes

    WORLD-BEAM QS30 LLP and LLPC Installation Notes Conventional retroreflective photoelectric sensors are extremely easy to align. Beam angles are wide, and retro targets are forgiving to the light beam’s angle of incidence. The beam of this laser sensor is very narrow, compared with the beam of most retro sensors. As Figure 6 indicates, the effect of angular misalignment can be dramatic.
  • Page 8: Specifications

    WORLD-BEAM QS30 LLP and LLPC Specifications Supply Voltage and Current Indicators 10 to 30V dc (10% max. ripple at 10% duty cycle) at 35 Output conducting mA max current, exclusive of load 8-Segment Red Bargraph Sensing Beam SETUP mode: Visible red LED, 650 nm •...
  • Page 9 WORLD-BEAM QS30 LLP and LLPC Description of Laser Classes Class 1 Lasers Lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. Reference IEC 60825-1:2001, Section 8.2. CAUTION: Do Not Disassemble for Repair Use of controls or adjustments or performance of proce- dures other than those specified herein may result in hazardous radiation exposure.
  • Page 10 WORLD-BEAM QS30 LLP and LLPC Hookups Cabled Models QD Models 10 - 30V dc 10 - 30V dc – – 150 mA max. load 150 mA max. load Load Load Load Load Remote Remote Teach Teach Note: Pink wire not used Accessories Quick-Disconnect Cables 5-Pin Threaded M12/Euro-Style Cordsets...
  • Page 11 9.14 m (30 ft) M12 x 1 ø 14.5 [0.57"] Retroreflective Targets For additional information and a complete list of accessories, please refer to Banner Engineering website http://www.bannerengineer- ing.com NOTE: Polarized sensors require corner cube type retroreflective targets only. BRT-2X2 BRT-51X51BM •...
  • Page 12: Banner Engineering Corp Limited Warranty

    Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period.

This manual is also suitable for:

Qs30llpcqQs30llpQs30llpc

Table of Contents