Basic Operation - Luna BBD 150 Original Instructions Manual

2. To turn machine "off", just need push the "emergency stop
cover" down. The emergency stop cover can located on the stop
position.
3. Any time when you need to stop the machine, easy to push the
emergency stop cover down.

BASIC OPERATION

Before using the sander
WARNING! To avoid mistakes that could cause serious,
permanent injury, do not plug the sander in until the fol-
lowing steps are completed.
1. Assembly and alignment
2. Learn the use and function of no-volt switch. Backstop, belt
tracking knob, belt tension lever, work table and work table tilt
lock knob.
3. Review and understand all safety instructions and operating
procedures in this manual.
4. Review of the maintenance methods for this sander.
Before each use
INSPECT YOUR SANDER
CAUTION. Disconnect the sander.
To avoid injury from accidental starting unplug the sander
before changing the setup, sanding disc or belt or adjusting
anything.
Check damaged parts. Check for
• alignment of moving parts
• binding or moving parts
• broken parts
• work parts that cause a gap larger than 1/16" between work sup-
port and sanding surface
• sanding belt narrower than 6 inches. Narrower belts uncover
parts that could trap your fingers.
• worn or damaged electric cords
• stable mounting, and
• any other conditions that may affect the way the sander works.
If any part is missing, bent, or broken in any way, or any electrical
parts don't work properly, turn the sander off and unplug the san-
der. REPLACE damaged, missing, or failed parts before using the
sander again.
MAINTAIN TOOLS WITH CARE. Keep the sander clean for
best and safer performance. Follow instructions for lubricating.
REMOVE ADJUSTING KEYS AND WRENCHES from tool
before turning it on.
WARNING! To avoid injury from jams, slips or thrown
pieces:
• USE ONLY RECOMMENDED ACCESSORIES. Consult
this owner's manual for recommended accessories. Follow the
instructions that come with the accessories. The use of improper
accessories may cause risk of injury to person.
• Adjust any work support to clear the sanding surface by no more
than 1/16". When checking clearance between the belt and work
support, press the belt that against the metal beneath it.
• Make sure all clamps locks are tight and no parts have excessi-
ve play.
• Keep work area clean. Cluttered areas and benches invite acci-
dent. Floor must not be slippery.
To avoid burns or other fire damage, never use the sander near
flammable liquids, vaports or gases.
PLAN AHEAD TO PROTECT YOUR EYES,
HANDS, FACE, EARS.
KNOW YOUR SANDER. Read and understand the owner's
manual and labels affixed to the tool. Lean its application and limi-
tations as well as the specific potential hazards peculiar to the tool.
To avoid injury from accidental contact with moving parts:
• KEEP GUARDS IN PLACE and in working order.
Don't do layout, assembly, or setup work on the sander while any
parts are moving.
PLAN YOUR WORK
USE THE RIGHT TOOL. Don't force tool or attachment to do a
job it was not designed to do.
CAUTION: This machine is not designed for heavy
deburring operations. When finishing metal, sparks or
hot fragments could cause a fire. To avoid this:
• Disconnet any dust collecting hose from the sander.
• Remove all traces of wood dust from inside the sander.
• Remove all traces of metal dust from inside the sander before
sanding wood again.
Dress for safety.
• Any power sander can throw foreign objects into the eyes. This
can cause permanent eye damage. Wear safety goggles.
• Do not wear loose clothing, gloves, neckties or jewelry (rings,
wrist watches). They can get caught and draw you into moving
parts.
• Wear nonslip footwear
• Tie back long hair.
• Noise levels vary widely. To avoid possible hearing damage,
wear ear-plug or muffs when using sander for hours at a time.
• Sanding operations are usually dusty. Wear a dust mask along
with safety goggles.
43