Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Carefree SUMMIT
Summary of Contents for Carefree SUMMIT
- Page 1 NSTALLATION ANUAL UMMIT AND UMMIT LIDE OVER WITH EAKED ONTOUR NSTALLER HEN COMPLETED WITH THE INSTALLATION CUT OFF THE LAST SHEET OF THIS MANUAL AND PLACE WITH THE COACH OWNER INFORMATION 052520-001r17 Printed in USA January, 2009 Table of Contents...
- Page 2 ROPRIETARY TATEMENT The Summit Slide-Out cover is a product of Carefree of Colorado, located in Broomfield, Colorado, USA. The information contained in or disclosed in this document is considered proprietary to Carefree of Colorado. Every effort has been made to ensure that the information presented in the document is accurate and complete.
-
Page 3: Table Of Contents
Mounting the Lift Bar Assembly ......................16 Installing the Roll Bar Assembly ......................17 Attaching the Optional Front Cover ......................18 Cover Bumpers ..........................19 Owner Information ........................A Maintenance ............................A Fabric Care ............................A Mildew ............................A Carefree Major Product Limited Warranty ..................... B 052520-001r17... -
Page 4: Summit Application Criteria
5. Additional layout requirements may restrict installations. Refer to the "Pre-Installation Layout" on page 4 for the Basic Summit. Refer to the "Pre-Installation Layout" on page 12 for the Summit XL. 052520-001r17 Table of Contents... -
Page 5: Component Checklist
Carefree of Colorado UMMIT NSTALLATION ASIC UMMIT OMPONENT HECKLIST SOK3004c Figure 2. Component Checklist ESCRIPTION Deflector Assy Bracket, Deflector Assy 2a Shim, 1/4", Deflector Bracket Cover, Bracket, Deflector Assy Roll Bar Assy Screw, Self Drilling, HWH #12 x 1 Screw, Self Drilling, HWH... - Page 6 NSTALLATION AYOUT Prior to installing a Summit with Lift-Bar, it is necessary to confirm the mounting requirements. If any of the parameters cannot be met, the optional Lift-Bar cannot be mounted correctly. Use a non-permanent method of marking, and mark the locations in this section. These will be used to mount the components.
- Page 7 Carefree of Colorado UMMIT ETTING THE EFLECTOR OUNTING RACKETS Bracket Cover Do Not Use Slot for Mounting Screws 1“ min Baseline “A” 12” max Deflector Assy #12 x 1 Self Drilling Screw Optional Shim Mounting Bracket SOK3016b Figure 7. Setting the Deflector Brackets.
- Page 8 Carefree of Colorado UMMIT NSTALLING AN AWNING RAIL IF REQUIRED Spread open the end of the Seal the back of the rail with silicone sealant or putty tape. awning rail Align the centerline of the awning rail with the layout marks made previously (refer to page 3).
- Page 9 Carefree of Colorado UMMIT VS R EFLECTOR ENGTH XTENSION CONT (59" – 105") EFLECTOR ENGTH (110" – 191") EFLECTOR ENGTH 052520-001r17 Table of Contents...
- Page 10 Carefree of Colorado UMMIT OUNTING THE SSEMBLY Threaded Outer Channel #7 x 7/16 Screw Carrier Screw Groove Style 1 Align Edge with Stop Bolt Positioning Mounting Pad Extension Scale (qty: 4) Groove DETAIL Style 2 #10 x 3/4 Lift Bar Assy...
-
Page 11: Installing The Roll Bar Assembly
Carefree of Colorado UMMIT NSTALLING THE SSEMBLY Polyrod Roll Bar Assy Awning Rail (ref) 1/4-20 x 3/4 Screw Completed Assembly SOK3011b Figure 13. Installing the Roll Bar Assembly. Close the room if open. Unroll some of the fabric from the roll bar. -
Page 12: Attaching The
The latching pin is spring loaded and will slide into the locking channel. Cover Bumpers The Summit cover is shipped with bumpers to prevent rattling. Quantities are two (2) for units under 10"; three (3) for units 10' to 12' and five (5) for units 12' and longer. -
Page 13: Component Checklist
Carefree of Colorado UMMIT NSTALLATION UMMIT OMPONENT HECKLIST 12 13 SOK3026a Figure 17. Component Checklist ESCRIPTION Deflector Assy Bracket, Deflector, Short 2a Bracket, Deflector, Long Alternate Cover, Bracket, Deflector Assy Roll Bar Assy Fabric Screw, Self Drilling, HWH #12 x 1... - Page 14 NSTALLATION AYOUT Prior to installing a Summit with Lift-Bar, it is necessary to confirm the mounting requirements. If any of the parameters cannot be met, the Lift-Bar cannot be mounted correctly. Use a non-permanent method of marking, and mark the locations in this section. These will be used to mount the components.
-
Page 15: Setting The Deflector Mounting Brackets W/ Lift Bar
Carefree of Colorado UMMIT ETTING THE EFLECTOR OUNTING RACKETS W Evenly Space Evenly Space Bracket Cover Additional Brackets Used w/ Rooms 283” or Longer Do Not Use Slot for Mounting Screws 1“ min, 12” max (typ) Baseline“A” #12 x 1 Self Drilling Screw... -
Page 16: Mounting The Deflector Assembly
Carefree of Colorado UMMIT OUNTING THE EFLECTOR SSEMBLY The deflector is shipped in two sections. The RH section has the RH end cap and the center splice assembly. The LH section has the LH end cap only. Splice Assy #10 x 1... - Page 17 Carefree of Colorado UMMIT ETTING THE OUNTING RACKETS Deflector Half Width #12 x 1 Self Drilling Screw (3 per bracket) “X” - see below “X” - see below Lift Bar Bracket Deflector (ref) SOK3035 Figure 22. Setting the Lift Arm Brackets.
-
Page 18: Mounting The Lift Bar Assembly
Carefree of Colorado UMMIT OUNTING THE SSEMBLY The lift bar assembly is shipped in two sections. Both consist of one lift bar section and two lift arm sets.. The first section has two splice plates attached to the lift bar. The second section has only one end cap. - Page 19 Carefree of Colorado UMMIT NSTALLING THE SSEMBLY NOTE: Because of the length and weight of the rollbar and fabric, it will be necessary to have 3 people to install the rollbar; one person at each end, with the third person to support the center.
- Page 20 Carefree of Colorado UMMIT TTACHING THE PTIONAL RONT OVER Mounting Holes Mounting Holes Spring-Loaded Attach Pins Spring-Loaded Pin Attach Spring-Loaded Attach Pins Center Cover Mount Latch Lever Cover Retaining Screws Threaded Screw Attach Cotter Pin Center Latch Pin Detail Detail...
-
Page 21: Cover Bumpers
Carefree of Colorado UMMIT Cover Bumpers The Summit cover is shipped with bumpers to prevent rattling. Quantities are three (3) for units under 14' and five (5) for units 14' and longer. To replace missing or damaged bumpers: 3. In the positions shown, fully press the first round section into the inner slot. This is the same slot that the latch springs are mounted in. - Page 22 Carefree of Colorado UMMIT 052520-001r17 Table of Contents...
-
Page 23: Maintenance
No anti-billow or locking devices required. AINTENANCE Maintaining the Carefree Summit is easy. Just follow these basic steps: • Periodically check that the fasteners are tight. Tighten if necessary. •... - Page 24 Carefree of Colorado (hereafter referred to as Carefree) warrants to the first retail Purchaser that the Carefree Product is free of defects in material and workmanship within the terms and conditions as set forth in the warranty statement available online at www.carefreeofcolorado.com. Carefree’s obligation under this warranty is limited to the repair or replacement, at Carefree’s option, of any defective component with new...