Specifications - Makita MLT100N Instruction Manual

ENGLISH (Original instructions)

SPECIFICATIONS

Model:
Arbor hole
&RXQWU\ VSHFL¿F
Blade diameter
Max. cutting capacities
No load speed
7DEOH VL]H / [ :
ZLWK VXE WDEOHV 5 DQG EDFN
'LPHQVLRQV / [ : [ +
ZLWK VXE WDEOHV 5 DQG EDFN
Net weight
Safety class
‡ 'XH WR RXU FRQWLQXLQJ SURJUDP RI UHVHDUFK DQG GHYHORSPHQW WKH VSHFL¿FDWLRQV KHUHLQ DUH VXEMHFW WR FKDQJH
without notice.
‡ 6SHFL¿FDWLRQV PD\ GLIIHU IURP FRXQWU\ WR FRXQWU\
‡ 7KH ZHLJKW PD\ GLIIHU GHSHQGLQJ RQ WKH DWWDFKPHQW V  7KH OLJKWHVW DQG KHDYLHVW FRPELQDWLRQ DFFRUGLQJ WR
EPTA-Procedure 01/2014, are shown in the table.
Symbols
The followings show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
DOUBLE INSULATION
Wear safety glasses.
'R QRW SODFH KDQG RU ¿QJHUV FORVH WR WKH
blade.
0DNH SURSHU FOHDUDQFH EHWZHHQ WKH VDZ
X~Xmm мм
( )
EODGH DQG ULYLQJ NQLIH
Only for EU countries
Do not dispose of electric equipment
together with household waste material! In
observance of the European Directive, on
Waste Electric and Electronic Equipment
and its implementation in accordance with
national law, electric equipment that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for cutting in wood.
Straight cutting, bevel cutting, and miter cutting are
available with this tool. This tool is not designed for non-
through cutting.
bevel 0°
bevel 45°
30 mm / 25.4 mm
 PP [  PP WDEOHV H[WHQGHG
 PP [  PP WDEOHV VWRUHG
 PP [  PP [ PP WDEOHV VWRUHG
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
IURP VRFNHWV ZLWKRXW HDUWK ZLUH
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-3-1:
Sound pressure level (L
Sound power level (L
8QFHUWDLQW\ .  G% $
NOTE: 7KH GHFODUHG QRLVH HPLVVLRQ YDOXH V KDV EHHQ
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: 7KH GHFODUHG QRLVH HPLVVLRQ YDOXH V PD\
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
9 ENGLISH
MLT100N
260 mm
93 mm
64 mm
-1
4,300 min
   NJ
/II
 G% $
pA
 G% $
WA