Maintenance; Optional Accessories - Makita MLT100N Instruction Manual

CAUTION:
Secure the knob on the miter
gauge carefully.
CAUTION:
Avoid creep of workpiece and
JDXJH E\ ¿UP ZRUNKROGLQJ DUUDQJHPHQW HVSH-
cially when cutting at an angle.
CAUTION:
NEVER hold or grasp the intended
"cut-off" portion of the workpiece.
CAUTION:
Always adjust the distance
between the end of the miter gauge and the saw
blade not to exceed 15 mm.
Use of miter gauge
Fig.41: 1. Miter gauge 2. Knob
6OLGH WKH PLWHU JDXJH LQWR WKH WKLFN JURRYHV LQ WKH WDEOH /RRVHQ WKH
NQRE RQ WKH JDXJH DQG DOLJQ WR GHVLUHG DQJOH ƒ WR ƒ  %ULQJ VWRFN
ÀXVK XS DJDLQVW IHQFH DQG IHHG JHQWO\ IRUZDUG LQWR WKH VDZ EODGH
Carrying tool
Fig.42
0DNH VXUH WKDW WKH WRRO LV XQSOXJJHG
&DUU\ WKH WRRO E\ KROGLQJ WKH WRRO SDUW VKRZQ LQ WKH ¿JXUH
CAUTION:
Always secure all moving portions
before carrying the tool.
CAUTION:
Before the carrying the tool, make
sure that the blade guard and the sub guard are
down and the lower edge of the sub guard con-
tacts with the main table.

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
Cleaning
Clean out sawdust and chips from time to time. Carefully
clean the blade guard and moving parts inside the table saw.
When removing the sawdust accumulated under the saw
blade, remove the table insert and use an air duster to blow
out the sawdust from the connector for a vacuum cleaner.
Lubrication
7R NHHS WKH WDEOH VDZ LQ WLSWRS UXQQLQJ FRQGLWLRQ DQG
to assure maximum service life, oil or grease the mov-
ing parts and rotating parts from time to time.
Lubrication places:
• Threaded shaft to elevate the saw blade
• Hinge to rotate the frame
• Elevation guide shafts on motor
• Gear to elevate the saw blade
• 6OLGLQJ SROHV RQ WKH VXE WDEOH 5 DQG VXE WDEOH EDFN
Replacing carbon brushes
&KHFN WKH FDUERQ EUXVKHV UHJXODUO\
5HSODFH WKHP ZKHQ WKH\ ZHDU GRZQ WR WKH OLPLW PDUN
Keep the carbon brushes clean and free to slip in the
holders. Both carbon brushes should be replaced at the
same time. Use only identical carbon brushes.
Fig.43: 1. /LPLW PDUN
1. 6WRUH WKH VXE WDEOH 5  5HPRYH WKH ULS IHQFH DQG
miter gauge if they are stored.
2. /RRVHQ WKH ORFN OHYHU DQG WXUQ WKH KDQGZKHHO XQWLO WKH VDZ
KHDG LV WLOWHG WR ƒ EHYHO DQJOH $IWHU WKDW WLJKWHQ WKH ORFN OHYHU
Fig.44: 1. Rip fence 2. Miter gauge 3. /RFN OHYHU
4. Handwheel
3. Stand the tool on its right side.
Fig.45
CAUTION:
Be sure to support the tool so as
not to let the tool fall down. It is recommended to
have someone to support the tool.
4. Loosen the screws on the bottom plate and remove it.
5. Loosen the brush holder caps using a screwdriver
and remove the worn carbon brushes.
Fig.46: 1. Bottom plate 2. Brush holder cap
3. Screwdriver
6. Insert the new carbon brushes and secure the
brush holder caps.
7. Attach the bottom plate with screws and carefully lay the
tool on its bottom. Store the rip fence and miter gauge if removed.
To maintain product SAFETY and RELIABILITY,
UHSDLUV DQ\ RWKHU PDLQWHQDQFH RU DGMXVWPHQW VKRXOG
EH SHUIRUPHG E\ 0DNLWD $XWKRUL]HG RU )DFWRU\ 6HUYLFH
&HQWHUV DOZD\V XVLQJ 0DNLWD UHSODFHPHQW SDUWV

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
VSHFL¿HG LQ WKLV PDQXDO The use of any other
DFFHVVRULHV RU DWWDFKPHQWV PLJKW SUHVHQW D ULVN RI
LQMXU\ WR SHUVRQV 2QO\ XVH DFFHVVRU\ RU DWWDFKPHQW
for its stated purpose.
If you need any assistance for more details regarding
WKHVH DFFHVVRULHV DVN \RXU ORFDO 0DNLWD 6HUYLFH &HQWHU
• Steel & Carbide-tipped saw blades
• Rip fence
• Miter gauge
• Wrench 24
• Hex wrench 5
‡ -RLQW IRU FRQQHFWLQJ WR GXVW FROOHFWRU
• Table stand set
Refer to the instruction manual for table saw stand that is
provided with the table saw stand as an optional accessory.
NOTE: Some items in the list may be included in the
WRRO SDFNDJH DV VWDQGDUG DFFHVVRULHV 7KH\ PD\
differ from country to country.
17 ENGLISH