Flo CoRe+ Max Installation Manual
Hide thumbs
Also See for CoRe+ Max:
- Installation manual (52 pages) ,
- Installation manual (15 pages) ,
- Installation manual (27 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Flo CoRe+ Max
Summary of Contents for Flo CoRe+ Max
- Page 1 CoRe+ Max Installation Manual...
-
Page 2: Table Of Contents
Table of Contents About CoRe+ Max Canada and USA Electromagnetic Interference Regulatory Statement Important Safety Instructions Instructions pertaining to a risk of fire or electric shock Important general safety instructions Important elements to consider when installing the communication gateway Installation Instructions... -
Page 3: About Core+ Max
About CoRe+ Max The CoRe+ Max is part of a family of Level 2 charging stations that are adaptable for a wide range of parking layouts including workplaces, condos, apartments, fleets, and commercial properties. They are ideal for sites where several high- capacity electric vehicles, such as commercial service trucks and school buses, need to charge simultaneously, because they can be cascaded to minimize installation costs for the entire site. -
Page 4: Important Safety Instructions
This symbol is used to provide awareness of important safety information in these instructions. WARNING: When using electric products, basic precautions should always be followed, including the following. This manual contains important instructions for Model CoRe+ Max that shall be followed during installation, operation, and maintenance of the unit. - Page 5 This product must be connected to a grounded, metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product and installed by a certified electrician. Any EVSE part alteration will automatically void the warranty. CoRe+ Max Installation Manual...
- Page 6 Install the Communication Gateway prior to the Commissioning of the Station. The Communication Gateway is the property of AddEnergie. Fees will be charged if the Gateway is damaged, lost or not installed according to the installation guide. CoRe+ Max Installation Manual...
-
Page 7: Important Elements To Consider When Installing The Communication Gateway
An Outdoor installation is recommended. The Customer must provide a waterproof PVC box and install it less than 48,7 meters (160 ft.) from the stations. Contact us when the Communication Gateway is installed to validate the signal levels and activate Commissioning or for any other questions: 1-877- 505-2674 #201 CoRe+ Max Installation Manual... -
Page 8: Installation Instructions
Installation Instructions Dimensions and nominal installation location. 2 matching holes and a rectangular cable opening when pedestal mounted. CoRe+ Max Installation Manual... -
Page 9: Power Cable Entry Under The Station
Make sure the conductors are long enough to reach the terminal block. Connect two power conductors (L1 and L2) and the ground conductor (GND). The grounding conductor shall be connected to the terminal ground. CoRe+ Max Installation Manual... -
Page 10: Power Cable Entry From The Back
Make sure the conductors are long enough to reach the terminal block. Connect two power conductors (L1 and L2) and the ground conductor (GND). The grounding conductor shall be connected to the terminal ground. CoRe+ Max Installation Manual... -
Page 11: With Electric Box
Connect two power conductors (L1 and L2) and the ground conductor (GND). The grounding conductor shall be connected to the terminal ground. CoRe+ Max Installation Manual... -
Page 12: Setting The Current Limit
Setting the current limit By default, the CoRe+ MAX is set to maximum power (factory). If your electrical infrastructure does not allow the charging station to operate at maximum power (or preventing any potential current overload), it can be reduced using the Current Limiter Switch. -
Page 13: Closing The Housing Of The Station
Make sure that the gasket on the lip shown below is well aligned. Connect the cables to their connectors as per the markings. Align the lip with the groove and install the head to the base, making sure that the seals stay in place. CoRe+ Max Installation Manual... - Page 14 Apply a slight pressure on the front cover, then screw on the top 2 bolts. Screw on the bottom 2 bolts. Tighten all screws to 30 lbs*in (3.4 N*m). ATTENTION: NEVER USE AN IMPACT DRIVER TO AVOID DAMAGING THE THREADS! Place the charging cable on the cable holder and the charging gun in receptacle. CoRe+ Max Installation Manual...
-
Page 15: Preliminary Tests And Commissioning
Station Status Light Indicator Green Solid color: Ready for session activation White Blinking: Session authenticated, ready to plug into EV Blue Solid color: Plugged in and energy being delivered Solid color: Critical fault Out of Service CoRe+ Max Installation Manual... -
Page 16: Power Sharing
(the specific model identification can be found on the unit label). Without a site controller installed or in operation, or in the event of a lost communication, each CoRe+ Max limits its output to 6A. To enable a dynamic sharing of current, a site controller must be installed and properly configured by AddEnergie. -
Page 17: Operating Instructions
Plug the connector into your vehicle. Charging will start immediately. Once charging is complete, replace the connector in its socket. WARNING: Once charging is complete, make sure to wind the cable and store the connector in its socket CoRe+ Max Installation Manual... -
Page 18: User Maintenance Instructions
User Maintenance Instructions The CoRe+ MAX enclosure complies to NEMA 4X which is intended for indoor or outdoor use primarily to provide a degree of protection against corrosion, windblown dust, rain, splashing water, and hose directed water; undamaged by ice which forms on the enclosure. -
Page 19: Specifications
Specifications Model: CoRe+ Max Revision: Company Info: AddEnergie Technologies Inc. Document revision number: V01-2021-02-27 ©2021 AddEnergie Technologies Inc. All Rights Reserved. This document is protected by copyright laws of many countries and should not be modified, reproduced, or distributed without the prior written consent of AddEnergie Technologies. - Page 20 Installation or commissioning questions: (877) 505-2674 ext. 201 AddÉnergie Technologies Inc. Contact Us 2800, Louis-Lumière Street, office 100, Québec (QC) G1P 0A4 CANADA T. 1 877 505-2674 F. 855 505-2674 info@addenergie.ca addenergie.com...