Flo Home X5 Installation Manual
Hide thumbs
Also See for FLO Home X5:
- Installation manual (3 pages) ,
- Installation manual (44 pages) ,
- Installation manual (40 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Flo FLO Home X5
Summary of Contents for Flo FLO Home X5
- Page 1 FLO Home X5 Model Installation Guide...
-
Page 2: Table Of Contents
-40°C to 50°C (-40°F to 122°F) Weight with cable, connector and mounting plate: 11.23 kg (24.76 lbs) Communication Interface: Power-line communication (PLC) MODEL NUMBER: FH-1-STA-X5-HY5N-FL1 MANUFACTURER: AddÉnergie Technologies Inc. December 2017 | flo.ca | Installation guide | FLO Home X5... -
Page 3: Safety Instructions
This charging station is to be used to charge vehicles that do not require a ventilated environment during charging. Always disconnect the power supply of the charging station before servicing. Do not put fingers into the electric vehicle connector. FLO Home X5 | Installation guide | flo.ca | December 2017... - Page 4 Recommended height to facilitate handling of the connector, as well as preventing the cable from touching the ground. 7,6 in 6,9 in 19,3 cm 17,5 cm 17 in 43,2 cm 60 in 152,4 cm Ground December 2017 | flo.ca | Installation guide | FLO Home X5...
-
Page 5: Planning Your Installation
Maximum output power: 7.2 kW @ 240 V or 6.2 kW @ 208 V Figure 1 Single-Phase 120/240 VAC 120 VAC 240 VAC Charging Station 120 VAC Ground Ground Figure 2 3-Phase 120/208 VAC 208 VAC Charging Station Ground FLO Home X5 | Installation guide | flo.ca | December 2017... -
Page 6: Installing The Station
The power supply cable can be inserted from the rear (a) or from under (b) the station: - 3/4 knockout (a) and (b) - Remove a single cap - Strain relief not included December 2017 | flo.ca | Installation guide | FLO Home X5... - Page 7 Secure the rear housing of the station to the mounting plate. Screw the lower screw to secure the mounting. FLO Home X5 | Installation guide | flo.ca | December 2017...
- Page 8 B) Tighten the 2 front screws with a nominal torque of 55 lbs-in. Detail A About 30° Switch on the electrical circuit breaker. Your new station can now charge your vehicle! December 2017 | flo.ca | Installation guide | FLO Home X5...
-
Page 9: Installing The Plc
Plug the PLC module into a wall outlet. Internet Router Electrical FLO Home Module panel Station Warning Do not connect the PLC module to an overvoltage protection device (surge protector), extension cord or power strip. FLO Home X5 | Installation guide | flo.ca | December 2017... -
Page 10: Checking The Plc Connection
- SOLID : The Ethernet port is connected to your router. - OFF : There is no Ethernet connection. *PLC : Power-line communication technology enables you to build a computer network on your home’s electrical network. December 2017 | flo.ca | Installation guide | FLO Home X5... -
Page 11: Associate The Station To Your Account
If your new station is not present in your account, you can add it using the association code that is included in the box. If you have not already done so, you can create your FLO account. Using your favorite web browser, go to https://flo.ca/signup... - Page 12 Enter the 16-character association code on the included card with your new station and click « Associate ». A message confirming the association should appear. Otherwise, contact our technical support for assistance. December 2017 | flo.ca | Installation guide | FLO Home X5...
-
Page 13: Light Indicators
Slow Blinking: The station cannot connect to the FLO server (check the PLC installation) Fast Blinking: The station is in configuration mode with the PLC module (after 3 minutes the terminal will restart) FLO Home X5 | Installation guide | flo.ca | December 2017... -
Page 14: Sound Indicator
- 2 long beeps: Major fault requiring a power interruption (please restart the station by cutting the power at the circuit breaker in the electrical panel for 10 seconds, then restore power) December 2017 | flo.ca | Installation guide | FLO Home X5... -
Page 15: Installation Of A Second Station
The charging terminal will automatically detect if it shares its power circuit with another FLO Home™ X5. - Power sharing can only be done between two FLO Home™ X5 charging stations. - When two stations are connected to the same circuit breaker, their output current will be limited to 16A. -
Page 16: Compliance
- CSA C22.2 No. 0.8-12 Safety functions incorporating electronic technology. - UL1998 Standard for software in programmable components. - UL991 Standard for Tests for Safety-Related Controls Employing Solid-State Devices. - NEC 2014 section 625. December 2017 | flo.ca | Installation guide | FLO Home X5... -
Page 17: Limited Warranty
Purchaser of the Product. 4.Limited Remedies. FLO’s obligations under this Limited Product Warranty are limited to repairing or replacing or reimbursing the purchase price, at FLO’s sole discretion, any Product which is found to be defective by FLO after proper inspection. -
Page 18: Assistance
8 AM ‑ 5 PM (ET), Monday to Friday 1‑855‑543‑8356 Technical support For any questions regarding charging station installation, configuration or any technical problem. 8 AM ‑ 5 PM (ET), Monday to Friday 1‑844‑825‑3356 December 2017 | flo.ca | Installation guide | FLO Home X5... -
Page 19: Charging Station Serial Number
Volt: 208 / 240 VAC 60Hz Courant max: 30A Amp: 30A max Boîtier / Enclosure: Type 4x Date Code: 201611 Operating Temp: -40 C to 50 FLO Home charging station bottom view FLO Home X5 | Installation guide | flo.ca | December 2017... - Page 20 2 Hold your smart phone at a 20 angle under the charging station. 3 Line up the phone screen with the serial number sticker 4 When you see the sticker take the picture. December 2017 | flo.ca | Installation guide | FLO Home X5...
- Page 21 THIS PAGE IS INTENTIONALLY LEFT BLANK...
- Page 22 THIS PAGE IS INTENTIONALLY LEFT BLANK...