Yeastar Technology S50 Installation Manual
Voip pbx
Hide thumbs
Also See for S50:
- Installation manual (13 pages) ,
- Administrator's manual (129 pages) ,
- Getting started manual (21 pages)
Related Manuals for Yeastar Technology S50
Summary of Contents for Yeastar Technology S50
- Page 1 Yeastar S50 VoIP PBX Installation Guide Version 1.0 June 22, 2016 https://arttel.ru/shop/ip-ats/yeastar-s50...
-
Page 2: Table Of Contents
Yeastar S50 Installation Guide Content Content………………………………………………………………………………………………………...2 Welcome……………………………………………………………………………………………………….3 Before You Start……………………………………………………………………………………………...4 Package Contents………………………………………………………………………………………….4 Hardware Overview………………………………………………………………………………………..4 LED Indicators and Ports………………………………………………………………………………….5 Installation…………………………………………………………………………………………………….7 Safety Disclaimers and Installation Warnings……………………………………………………………7 Module Installation………………………………………………………………………………………….7 Desktop Installation……………………………………………………………………………………….10 Rack Installation ………………………………………………………………………………………….10 Ground Connection………………………………………………………………………………………..11 Connecting the Equipment……………………………………………………………………………….12 Getting Started with the Configuration…………………………………………………………………13 2/13 https://arttel.ru/shop/ip-ats/yeastar-s50... -
Page 3: Welcome
ISDN BRI, PSTN, and GSM connectivity, providing VoIP communications for up to 50 users. This guide describes how to install the S50 and how to log in the web GUI to configure the system. Once you complete the installation, refer to the Yeastar S-Series Administrator Guide for instructions on how to perform configurations on the system. -
Page 4: Before You Start
Yeastar S50 Installation Guide Before You Start Before you begin to install the S50 IP Phone System, please check the package contents to verify that you have received the items below. If there is any problem, please contact your provider. -
Page 5: Led Indicators And Ports
Rotate the antenna into the Antenna Socket. SD Slot Insert a SD card. Yeastar S50 supports two 10/100/1000M Ethernet ports. Ethernet Port LAN port: LAN port is for the connection to Local Area Network (LAN). - Page 6 Yeastar S50 Installation Guide supports „DHCP server‟, „PPPoE/dynamic DNS‟, and “static IP” for IP address assignment. Reset Button Press and hold for 10 seconds to restore the factory defaults. Power Inlet Connect the supplied power supply to the port.
-
Page 7: Installation
Before cleaning the device, cut off the power supply. Environment Install the Yeastar S50 IP PBX in a location that is clean, free from vibration, electric shock, and temperature/humidity extremes. The operating temperature should be kept below 104° F (40° C). Module Installation Yeastar S50 supports installing up to 2 modules. - Page 8 Yeastar S50 Installation Guide STEP 1 Loosen the screws on the enclosure and then remove the upper cover. STEP 2 Insert the module to the Module Slot. STEP 3 Insert a SIM card on the GSM/CDMA/3G module following the instructions. Skip this step if no GSM/CDMA/3G module installed.
- Page 9 Yeastar S50 Installation Guide STEP 4 Fix the screws and close the cover. STEP 5 Rotate the antenna into the Antenna Socket. Skip this step if no GSM/CDMA/3G module installed. 9/13 https://arttel.ru/shop/ip-ats/yeastar-s50...
-
Page 10: Desktop Installation
Yeastar S50 Installation Guide Desktop Installation WARNING Please set 5~10cm gaps around the device for air circulation. Please avoid any heavy thing placed on the device. STEP 1 Place the IP PBX on a steady platform. STEP 2 Remove the adhesive backing paper from the rubber feet. -
Page 11: Ground Connection
Yeastar S50 Installation Guide STEP 2 Place the PBX in the 19-inch rack and fix both brackets to the rack with the rack‟s proprietary mounting equipment. Ground Connection WARNING Proper grounding (connection to ground) is very important to reduce the risk to the user of electrocution or protect the PBX from the bad effects of external noise in the case of a lightning strike. -
Page 12: Connecting The Equipment
ISDN provider equipment. STEP 2 Plug the provided power cord into the power jack on S50 and the other end to a standard electrical wall socket. Wait for the system to boot up till the SYSTEM LED starts to blink. -
Page 13: Getting Started With The Configuration
Yeastar S50 Installation Guide Getting Started with the Configuration Yeastar S50 IP Phone System provides web-based configuration interface for administrator. The administrator can manage the device by logging in the Web interface. Access path: https://192.168.5.150:8088 User Name: admin ...