Yeastar Technology S20 Installation Manual
  1. Manuals
  2. Brands
  3. Yeastar Technology Manuals
  4. PBX
  5. S20
  6. Installation manual

Yeastar Technology S20 Installation Manual

Hide thumbs Also See for S20:

Advertisement

Table of Contents

See also: Administrator's Manual
Yeastar S20 VoIP PBX
Installation Guide
Version: 1.2
Date: 2016.09.02

Advertisement

Table of Contents
loading

Related Manuals for Yeastar Technology S20

Summary of Contents for Yeastar Technology S20

  • Page 1 Yeastar S20 VoIP PBX Installation Guide Version: 1.2 Date: 2016.09.02...

  • Page 2: Table Of Contents

    Yeastar S20 Installation Guide Content Welcome ....................................3 Before You Start ................................4 Package Contents ............................4 Hardware Overview ............................. 4 LED Indicators and Ports..........................5 Installation ..................................7 Safety Disclaimers and Installation Warnings ....................7 Module Installation ............................7 Desktop Installation ...........................

  • Page 3: Welcome

    FXS, PSTN, ISDN BRI, and GSM/3G. This guide describes how to install the S20 and how to log in the web GUI to configure the system. Once you complete the installation, refer to the Yeastar S-Series Administrator Guide for instructions on how to perform configurations on the system.

  • Page 4: Before You Start

    Yeastar S20 Installation Guide Before You Start Before you begin to install the S20 IP Phone System, please check the package contents to verify that you have received the items below. If there is any problem, please contact your provider.

  • Page 5: Led Indicators And Ports

    Yeastar S20 Installation Guide LED Indicators and Ports LED Indicators Indication Status Description The power is switched on POWER Power status The power is switched off Blinking The system is running properly System System status Static/Off The system goes wrong Static Linked normally.
  • Page 6 Yeastar S20 Installation Guide Yeastar S20 provides two 10/100M adaptive RJ45 Ethernet ports. There are 3 Ethernet modes for the system. The default mode is “Single”.  Single: LAN port interface will be used for uplink connection. WAN port is Ethernet Port disabled.

  • Page 7: Installation

    Before cleaning the device, cut off the power supply.  Environment Install the Yeastar S20 IP PBX in a location that is clean, free from vibration, electric shock, and temperature/humidity extremes. The operating temperature should be kept below 104° F (40° C). Module Installation Yeastar S20 supports installing up to 2 modules.
  • Page 8 Yeastar S20 Installation Guide STEP 1 Loosen the screws on the bottom of the device and remove the upper cover. STEP 2 Insert the module to the Module Slot. STEP 3 Insert a SIM card on the GSM/3G module following the instructions. Skip this step if no GSM/3G module installed.
  • Page 9 Yeastar S20 Installation Guide STEP 4 Close the cover and fix the screws. STEP 5 Rotate the antenna into the Antenna Socket. Skip this step if no GSM/3G module installed. 9/12...

  • Page 10: Desktop Installation

    Yeastar S20 Installation Guide Desktop Installation WARNING  Please set 5~10cm gaps around the device for air circulation.  Please avoid any heavy thing placed on the device. STEP 1 Place the IP PBX on a steady platform. STEP 2 Remove the adhesive backing paper from the rubber feet.

  • Page 11: Connecting The Equipment

    Yeastar S20 Installation Guide Connecting the Equipment STEP 1 Connect one end of a network cable to the LAN port of Yeastar S20, and the other end to any port of your company’s LAN switch/router. STEP 2 Plug the provided power adapter into the power jack on S20 and the other end to a standard electrical wall socket.

  • Page 12: Getting Started With The Configuration

    Yeastar S20 Installation Guide Getting Started with the Configuration Yeastar S20 IP Phone System provides web-based configuration interface for administrator. The administrator can manage the device by logging in the Web interface.  Access path: https://192.168.5.150:8088  User Name: admin ...

Table of Contents