Maintenance - DeWalt DWS713 Original Instructions Manual

For Cutting Crown Molding Laying Flat and Using the Compound
Features (Fig. T)
1. Move the sliding fence 10 out of the path of the blade before attempting any of the
following cuts.
2. Molding laying with broad back surface down flat on saw table
BEVEl sETTing
lEFT siDE, insiDE CORnER
1. Top of molding against fence
33.9°
2. Mitre table set right 31.6°
3. Save left end of cut
RighT siDE, insiDE CORnER
1. Bottom of molding against fence
33.9°
2. Mitre table set left 31.6°
3. Save left end of cut
lEFT siDE, OUTsiDE CORnER
1. Bottom of molding against fence
33.9°
2. Mitre table set left 31.6°
3. Save right end of cut
RighT siDE, OUTsiDE CORnER
1. Top of molding against fence
33.9°
2. Mitre table set right 31.6°
3. Save right end of cut
When setting bevel and mitre angles for all compound mitres, remember that:
The angles presented for crown moldings are very precise and difficult to set exactly. Since
they can easily shift slightly and very few rooms have exactly square corners, all settings should
be tested on scrap molding.
PRETEsTing WiTh sCRAP MATERiAl is EXTREME lY iMPORTAnT!
Alternative Method for Cutting Crown Molding (Fig. U)
Place the molding on the table at an angle between the sliding fence
table , as shown in Figure U. Use of the crown molding fence accessory (DW7084) is highly
36
recommended because of its degree of accuracy and convenience. The crown molding fence
accessory is available at extra cost from your local dealer.
The advantage to cutting crown molding using this method is that no bevel cut is required.
Minute changes in the mitre angle can be made without affecting the bevel angle. This way,
when corners other than 90° are encountered, the saw can be quickly and easily adjusted for
them. Use the crown molding fence accessory (DW7084) to maintain the angle at which the
molding will be on the wall.
Instructions for Cutting Crown Molding Angled Between the Fence and
Base of the Saw for All Cuts (Fig. U)
1. Angle the molding so the bottom of the molding (part which goes against the wall when
installed) is against the fence and the top of the molding is resting on the base of the saw,
as shown in Figure U.
2. The angled "flats" on the back of the molding must rest squarely on the fence and base of
the saw.
inside corner
1. Mitre right 45°
Left side
2. Save right side of cut
1. Mitre left 45°
Right side
2. Save left side of cut
Special Cuts
NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON THE TABLE AND AGAINST
THE FENCE.
Aluminum Cutting (Fig, A, V, W)
ALWAYS USE THE APPROPRIATE SAW BLADE MADE ESPECIALLY FOR CUTTING ALUMINUM.
These are available at your local D WALT retailer or D
e
due to their size, shape or surface finish, may require the use of a clamp or fixture to prevent
movement during the cut. Position the material so that you will be cutting the thinnest cross
section, as shown in Figure V. Figure W illustrates the wrong way to cut these extrusions. Use
a stick wax cutting lubricant when cutting aluminum. Apply the stick wax directly to the saw
blade before cutting. Never apply stick wax to a moving blade.
26
The wax, available at most hardware stores and industrial mill supply houses, provides proper
lubrication and keeps chips from adhering to the blade.
Be sure to properly secure workpiece. Refer to Saw Blades under Optional Accessories for
correct saw blade.
Bowed Material (Fig. X, Y)
When cutting bowed material always position it as shown in Figure X and never like that
shown in Figure Y. Positioning the material incorrectly will cause it to pinch the blade near the
completion of the cut.
Cutting Plastic Pipe or Other Round Material
Plastic pipe can be easily cut with your saw. It should be cut just like wood and ClAMPED
OR hElD FiRMlY TO ThE FEnCE TO KEEP iT FROM ROlling. This is extremely important
when making angle cuts.
36 (Fig. T).
TYPE OF CUT
10 and the saw
Outside corner
1. Mitre left 45°
2. Save right side of cut
1. Mitre right 45°
2. Save left side of cut
WALT service centre. Certain workpieces,
e
Cutting Large Material (Fig. L)
Occasionally you will encounter a piece of wood a little too large to fit beneath the blade
guard. A little extra height can be gained by rolling the guard up out of the way, as shown in
Figure L. Avoid doing this as much as possible, but if need be, the saw will operate properly
and make the bigger cut. NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD OPEN WHEN
OPERATING THIS SAW.

MAINTENANCE

Your power tool has been designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories. An accidental start-up can cause injury.
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic
guard. The polycarbonate material used in the guard is subject to attack by certain chemicals.
1. All bearings are sealed. They are lubricated for life and need no further maintenance.
2. Periodically clean all dust and wood chips from around AND UNDER the base and the
rotary table. Even though slots are provided to allow debris to pass through, some dust
will accumulate.
3. The brushes are designed to give you several years of use. To replace the brushes, return
the tool to the nearest service centre for repair. A list of service centre locations is packed
with your tool.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Consult your dealer for further information on the appropriate accessories.
The following accessories, designed for your saw, may be helpful. In some cases, other locally
obtained work supports, length stops, clamps, etc., may be more appropriate. Use care in
selecting and using accessories.
Adjustable length stop: DW7051
Requires the use of one work support. It is used to make repetitive cuts of the same length
from 0 to 107 cm.
Clamp: DW7082
Used for firmly clamping workpiece to the saw fence for precision cutting.
Dust Bag: DW7053
included with some models
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the
sawdust produced.
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Mitre saw stands: DWX723, DE7260, DE7033
Provides stable and accurate work platform for mitre saws.
saw Blades
ALWAYS USE 254 mm SAW BLADES WITH 16 mm ARBOUR HOLES. SPEED RATING MUST BE
AT LEAST 5500 RPM. Never use a smaller diameter blade. It will not be guarded properly. Use
crosscut blades only! Do not use blades designed for ripping, combination blades or blades
with hook angles in excess of 7 degrees.
BLADE DESCRIPTIONS
APPLICATION
Construction Saw Blades (thin kerf with anti-stick rim)
General purpose
Fine crosscuts
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
Non-ferrous metals
NOTE: For cutting non-ferrous metals, use only saw blades with TCG teeth designed for this purpose.
WALT, have not been tested
e
DIAMETER TEETH
254 mm 40
254 mm 60
254 mm 80
254 mm 80
English
11