Advertisement
•視窗顯示 /The panel shows：
車縫結束，壓腳停止踩踏後，可設定延遲關閉
吸風集塵的時間。設定值 0 ～ 30。
0：表示延遲 0 秒關閉；
30：表示延遲 3.0 秒關閉。
•視窗顯示 /The panel shows：
按馬達轉動鍵時，步進馬達轉動方向。設定值
0 ～ 1。
0：表示步進馬達退帶；
1：表示步進馬達送帶。
•視窗顯示 /The panel shows：
切刀動作後，回踩踏板會執行送帶動作。送帶
完成後，回踩踏板是否執行上 / 下吹風動作。
設定值 0 ～ 1。
0：表示送帶後，回踩踏板不執行上 / 下吹風
1：表示送帶後，回踩踏板執行上 / 下吹風
•視窗顯示 /The panel shows：
設定切刀閉合的時間。設定值 5 ～ 50。
5 ：表示切刀閉合時間為 50ms；
50：表示切刀閉合時間為 500ms。
•視窗顯示 /The panel shows：
設 定 車 縫 結 束 是 否 啟 動 鬆 線 功 能。 設 定 值
0~1。
0：表示車縫結束不啟動鬆線功能；
1：表示車縫結束啟動鬆線功能。
•視窗顯示 /The panel shows：
設定延遲啟動送帶功能的時間。設定值 5 ～
80。
5：表示當車縫結束後偵測到回踩踏板動作時，
延遲 50ms 才啟動送帶功能。
80：表示當車縫結束後偵測到回踩踏板動作
時，延遲 800ms 才啟動送帶功能。
P .S：當車頭伺服馬達設定車縫停止針棒停在
下停針位置，此時回踩踏板，伺服馬達
會運轉到上停針位置的設定狀態，為避
免伺服馬達運轉帶動檢知器而被系統誤
判，並中斷送帶動作造成送帶長度不準
確，建議此參數調整成 25 以上。
8 ET-H Ti 5
9 CCW-CW 1
10 AIR - 1
11 CUT CT 15
12 TR ACT 1
13 INS DT 25
•Set the time for which the function of gathering
the lint through suction delays ending after
the sewing is completed and the pedal is not
stepped on. The setting values are 0~30.
0 indicates the time is 0 second;
30 indicates the time is 3.0 seconds.
•Set the rotation direction of the step motor after
the motor operating key is pressed. The setting
values are 0~1.
0 indicates that the step motor withdraws the tape;
1 indicates that the step motor feeds the tape.
•After the trimmer is done with its task, the back
pedal will feed the tape.After feeding the tape,
should the back pedal execute the top / bottom
blow device. The setting value 0 & 1:
0: It indicates that after feeding tape, the back pedal
would not execute the top / bottom blow device.
1: It indicates that after feeding tape, the back
pedal would execute the top / bottom blow device.
•Set the timing of the trimmer closure. The setting
value is 5 ~ 50.
5: It indicates that the timing of the trimmer
closure is 50ms;
50: It indicates that the timing of the trimmer
closure is 50ms.
•Set to check if the function of loosing wire is
turned on after the accomplishment of sewing.
The setting value is 0 ~ 1.
0: It indicates that the function is not turned on
after the sewing.
1: It indicates that the function is turned on after
the sewing.
•Set the time of delaying the feeding function
start. The setting value is 5~80.
5: indicates When the completion of sewing and
the backward tread action is detected, the
feeding function will start after delaying 50ms.
80: indicates When the completion of sewing and
the backward tread action is detected, the
feeding function will start after delaying 800ms.
P .S: When the machine servo motor is set to drop
the needle at the position of bottom stop
needle as the sewing stops, tread the pedal
at the moment, and the servo motor will rotate
to let the needle drop at the setting state of
top stop needle position. In order to avoid
the system error because the servo motor's
Introduction
P20
Advertisement
