Advertisement
參數說明
•視窗顯示 /The panel shows：
送帶長度設定，設定值 0 ～ 200。
0：表示送帶 0mm；
200：表示送帶 200mm。
•視窗顯示 /The panel shows：
步進馬達送帶速度設定，設定值 1 ～ 99。
1：表示送帶速度最慢；
99：表示送帶速度最快。
•視窗顯示 /The panel shows：
起縫時鬆緊帶拉回長度設定，設定值 0 ～ 60。
0：表示拉回 0mm；
60：表示拉回 60mm。
•視窗顯示 /The panel shows：
切刀動作延遲時間，設定值 0 ～ 800。
0：表示延遲 0 mS；
800：表示延遲 800 mS。
•視窗顯示 /The panel shows：
切刀動作完成後，車縫剩餘鬆緊帶所需的針
數。設定值 0 ～ 99。
0：表示所需針數 0 針；
99：表示所需針數 99 針。
P .S.：
1. 參數 12 設定值為 1 時，所需針數車縫完成
後，會自動啟動鬆線與吸風集塵功能。
2. 參數 12 設定值為 0 時，所需針數車縫完成
後，只會自動啟動吸風集塵功能。
•視窗顯示 /The panel shows：
縫製功能完成後，壓腳是否自動提升。設定值
0 ～ 1。
0：表示關閉此功能；
1：表示開啟此功能。
•視窗顯示 /The panel shows：
車縫開始時自動啟動吸風集塵功能，可設定
幾針後關閉。設定值 0 ～ 99。
P19
1 INS L 50
•Set the length of the tape which is fed. The setting
2 INS Sp 50
•Set the speed at which the step motor feeds the
3 Back L 15
•Set the length of the tape which is pulled back at
4 CUT Ti 150
•Set the time for which the trimmer delays cutting the
5 CUT St 10
•The accomplishment of the trimmer, the needle
6 Foot Up 0
•Set whether the presser foot is raised automatically
7 OFF St 10
•Set the number of stitches after which the function
THE ILLUSTRATION OF
THE PARAMETERS
values are 0~200.
0 indicates the length is 0mm;
200 indicates the length is 200mm.
tape. The setting values are 1~99.
1 indicates the speed is the lowest;
99 indicates the speed is the highest.
the start of sewing. The setting values are 0~60.
0 indicates the length is 0mm;
60 indicates the length is 60mm.
thread. The setting values are 0~800.
0 indicates the time is 0 ms;
800 indicates the time is 800 ms.
numbers which need to sewing the rest elastic belt.
The setting value is 0 ~ 99.
0: It indicates that the needful needle numbers is 0.
99: It indicates that the needful needle numbers is 99.
P .S.:
1. If the setting value of the parameter 12 is 1, after
the accomplishment of the sewing, it performs
the function of loosing wires and the suction
automatically.
2. If the setting value of the parameter 12 is
0, after the accomplishment of the sewing,
it only performs the function of the suction
automatically.
after the function of sewing is completed. The
setting values are 0~1.
0 indicates the function is off;
1 indicates the function is on.
of gathering the lint through suction starting at the
beginning of sewing ends. The setting values are
0~99.
0 indicates the number of stitches is 0;
99 indicates the number of stitches is 99.
Advertisement
