Table of Contents
Advertisement
Available languages
Available languages
Quick Links
Advertisement
Table of Contents
Related Manuals for Siruba 700K
Summary of Contents for Siruba 700K
- Page 1 電控參數說明書 ELECTRONIC CONTROL PARAMETER MANUAL 700K(BKF)
-
Page 2: Table Of Contents
目 次 頁次 1. 安裝衣襬尺寸導引器 / Welt Guide Installation…………………………………………………….. 2. 檢查及校正位置檢測器 / Checking and Positioning the Position Detector………………………….. 3. 校位及調整衣襬尺寸導引器 / Positioning and Adjusting the Welt Guide………………………………... A. 盲縫平縫區 Blind Stitch Hemming the Flat Seam Section……………………………………………….. 盲縫段縫部 Blind Stitch H emming the Cross Seam Section……………………………………………. 4. -
Page 3: 安裝衣襬尺寸導引器 / Welt Guide Installation
1. 安裝衣襬尺寸導引器 / Welt Guide Installation A.左右調整將左邊的可撇式導板和落針處中心線對齊。 Making a left or right adjustment, to align the left side of the retractable guide with the center line of the needle. B.前後調整可將可撇式導板尾端對齊切刀。 Making a forward or backward adjustment, to align the end of the retractable guide with the cutter. -
Page 4: 檢查及校正位置檢測器 / Checking And Positioning The Position Detector
檢查及校正位置檢測器 / Checking and Positioning the Position Detector A.電源開啟 Turn power ON. B.檢查指示燈是否有亮 Check whether the indicator lamp is on. 指示燈 Indicator lamp... - Page 5 C. 輕壓檢測器確認位置，檢測器是否亮燈。 Press the detector lightly in to confirm that the cross seam section detector lamp turns on. ⑴未碰觸時，指示燈① OFF，指示燈② ~ ⑥ ON。 Without touching, NO.1 detector lamp is OFF, NO.2~NO.6 detector lamps are ON. ⑵輕壓到底，指示燈① ON，指示燈② ~ ⑥ OFF。 Press the detector lightly, NO.1 detector lamp is ON, NO.2~NO.6 detector lamps are OFF.
- Page 6 E. 調整感測器位置 / Adjusting the Sensor Position ⑴鬆開固鎖螺絲。 Loosen the locking screw. ⑵使用三用電表，量測感測器輸出電壓(DC)。 Use multimeter meter to measure the output DC voltage of sensor. ⑶旋轉調節螺絲，調整感測器位置，使感測器輸出電壓介於 DC0.5~0.6V，此時鎖緊固鎖螺絲固定感測器位置。 As shown in the following figure, rotate the adjustment screw to adjust the position of sensor, make the output DC voltage of sensor lie within 0.5 ~ 0.6V, and then tighten the locking screw to secure the position of sensor.
-
Page 7: 校位及調整衣襬尺寸導引器 / Positioning And Adjusting The Welt Guide
3. 校位及調整衣襬尺寸導引器 / Positioning and Adjusting the Welt Guide 為了防止漏縫，當檢測器檢測到段縫時，可撤式導板會內移，將布料也往內移，如圖所示。接著， 操作盲縫以好的線跡蓋過段縫。蓋過段縫後，可撤式導板會外移回歸原位，恢復正常盲縫操作， 如圖所示。 In order to prevent skip stitching, when a cross seam is detected by the sensor, the retractable guide starts moving inside and moving the fabric inward, as shown in the following figure. Then, the cross seam section is sewn over with fine stitches in blind stitch hemming operation. -
Page 8: 盲縫平縫區 Blind Stitch Hemming The Flat Seam Section
A.盲縫平縫區 Blind Stitch Hemming the Flat Seam Section. 平縫區 若縫寬度過大時，順時針旋 若縫寬度過小時，反時針旋轉調 轉調節螺絲 節螺絲 Flat seam section If the seam width is too If the seam width is too narrow wide, turn the adjusting turn the adjustment screw screw clockwise. counter clockwise. 調整調節螺絲... -
Page 9: 盲縫段縫部 Blind Stitch H Emming The Cross Seam Section
盲縫段縫部 Blind Stitch Hemming the Cross Seam Section. 如在段縫處前後布料漏縫, 若段縫處前後縫寬過大，順 段縫部 時針旋轉螺帽 逆時針轉螺帽 Cross seam section If the stitches are missing If the seam width is too before and after the cross wide before and after the seam section, turn the nut cross seam section, turn the counter clockwise. -
Page 10: 檢查及調整摺疊器 / Checking And Adjusting The Folder
4. 檢查及調整摺疊器 / Checking and Adjusting the Folder 將摺疊器前緣和檢測器的間隔調整成縫紉布料的厚度。 Adjust the gap between the leading edge of the folder and the detector into the thickness of the fabric to be sewn. 織物厚度 The thickness of the fabric to be sewn. -
Page 11: 控制箱說明 / Description Of The Control Box
5. 控制箱說明 / Description of the Control Box A. 前視圖 / Front View 電源開關 Power switch 伺服馬達操作面板 Servo Motor control panel 跨越縫檢測器調整鈕 Cross seam detector adjustment knob... -
Page 12: 後視圖 / Rear View
B. 後視圖 / Rear View CROSS SEAM DETECTOR REVOLUTION OUT HALL PULSE OUT PULSE OUT 4 0V 4 0V AC POWER IN GIDE DC+12V LAMP 1 +24V +24V GUDE +12V +12V LAMP MOTOR FOLDER SW. FOOT LIFTER FOLDER SW. 1 +24V +24V REVOLUTION OUT A.F.L. -
Page 13: 跨越縫檢測器調整 / Adjusting The Cross Seam Detector
6. 跨越縫檢測器調整 / Adjusting the Cross Seam Detector 開啟電源 / Turn on the power 紅燈跨越縫檢測器位置顯示 Cross seam poistion indicated by red LEDs. 黃燈燈亮代表啟動跨越縫機能 Start cross seam while the yellow LED up. 紅燈 黃燈 依布料需要跨越縫的厚度調整旋鈕至黃燈亮 Adjust the knob to lit the yellow LED according the thickness of fabric. 黃燈... -
Page 14: Gude 針數設定 / Setting Gude Stitch Numbers
7. GUDE 針數設定 / Setting GUDE Stitch Numbers A. 吸風功能：(按 S 鍵，讓"_"符號位置在上方) Suction function：(Press S key, change "-" to top side) a. 前吸風針數設定 (畫面顯示 05) Setting stitches of the front suction. （Display “05”） b. 後吸風針數設定 (畫面顯示 35) Setting stitches of the real suction.（Display “35”） ＊必須使用光電開關... -
Page 15: 自動拷下擺功能 / Retractable Guide
C. 自動拷下擺：(按 s 鍵 讓"_" 符號在下方位置) Retractable Guide：(Press S key, change "-" to bottom side) a. 自動拷下擺開啟 (畫面顯示 03) Turn on the Electric Hemming Guide. （Display “03”） b. 自動拷下擺關閉 (畫面顯示 05) Turn off the Electric Hemming Guide. (Display “05”) AB 值與 CD 值的規則為： The rule of AB and CD values：... - Page 16 七段顯示器字體與實際數值對照表 : 7-Segment Display Characters Compare Table 數值字體部份 : （Arabic Numerals） 實際數值 Actual 七段顯示器 Display 英文字體部份 : （English Alphabet） 英文數字 （Actual） 七段顯示器 （Display） 英文數字 （Actual） 七段顯示器 （Display） 英文數字 （Actual） 七段顯示器 （Display） 版權所有．仿冒必究 Violators will be prosecuted...
- Page 17 由於對產品的改良及更新 , 本產品使用說明書中與零件圖之產品及外觀的修改恕不事先通知 ! The specification and/or the equipment described in the instruction book and parts list are subject to change because of modification with out previous notice AUG.2020...