Advertisement
Quick Links
Advertisement
Related Manuals for fantastic furniture Ryan
Summary of Contents for fantastic furniture Ryan
- Page 1 Assembly Instructions Ryan 3 Door Robe 1200mm - Oak...
- Page 2 It is recommended the wardrobe is assembled in the room that it is intended for. (CLEAR FLOOR SPACE IN ROOM IF REQUIRED)
- Page 3 Hammer 1 x HANGING RAIL 3 x 28MM NIB SCREW 50 x NAILS (H4) (H2) 2 x T Z FITTING (H3) (H1) 12 x CONFIRMAT SCREW CAPS 16 x CONFIRMAT SCREWS (H7) 8 x SHELF SUPPORTS (H6) (H8) 2 x HANGING RAIL BRACKETS 3 x BOW HANDLES (H5) (H11)
- Page 4 STEP 1 You will need: Note: All raw edges should be 2 x T Z Fitting (H1) facing up and Oak edges facing down in this stage of assembling Towards top edge TZ Fitting (H1) Knock into Parts 1 Insert TZ fittings in to P1 and tap in with mallet. Align dowels on P2 with holes on P5 and bring together.
- Page 5 STEP 2 You will need: Note: 10 x Confirmat Screws (H6) All raw edges should be facing up and Oak edges facing down in this stage of assembling 6 x Confirmat screw Caps (H7) Insert the panel P4 between panels P2 & P6, align dowels with holes and bring together.
- Page 6 STEP 3 You will need: 6 x Confirmat Screws (H6) Note: All raw edges should be facing up and Oak edges facing down in 6 x Confirmat Screw Caps (H7) this stage of assembling 2 x 28mm Nib Screw (H2) 28MM NIB SCREW THROUGH TZ...
- Page 7 STEP 4 Profile view of connector strip of backs P8 Top Of Strip P13 You will need: 50 x nails (H3) Note: Top of strip (P13) to be facing upwards when placing it on unit 6 x Plastic Glides (H13) White Edge down Ensure the unit is on it's front, raw edge up, Oak edge facing down Join the 2 smaller back panels (P8) with the connect strip (P13) as shown...
- Page 8 STEP 5 You will need: 2 x Hanging Rail Brakets(H5) 6 x Hinge Block (H10) 8 x Shelf Supports (H8) 2 x 1/2 6G C/S Screw (H9) FACING FACING REAR OF FRONT UNIT OF UNIT When attaching the hinge block (H10) ensure that it is positioned as shown above.
- Page 9 STEP 6 You will need: 6 x Hinge (H10) 1/2 6G C/S Screw (H9) 14 x 1/2 6G C/S Screw (H9) Hinge (H10) P10 & P11 Snap-On System The hinge arm is positioned on the mounting plate and simply clipped on from front to back.
- Page 10 STEP 7 You will need: 3 x Bow Handle (H11) 6 x Handle Screw (H12) 1 x Wall Fixing Bracket (H14) 1 x 28mm Nib Screw (H2) To fit handles, place handles (H11) on the front of the door and use Handle Screw (H12) to fix handle to the door from the inside of the unit.
- Page 11 STEP 8 Page 11...
- Page 12 YOUR UNIT IS NOW COMPLETE In the interest of our environment Please dispose of all packaging thoughtfully. CAUTION We recommend all units to be screwed to the wall . Consult your hardware specialist for which fastener is recommended. Page 12...