Advertisement
Quick Links
Advertisement
Related Manuals for WATSON Edison Junior Rail
Summary of Contents for WATSON Edison Junior Rail
- Page 1 ASSEMBLY Edison Junior Rail 360.394.1300 watsonfurniture.com V.21.00 05/2021...
- Page 2 WARNINGS WARNING - Risk of Fire or Electric Shock. It is possible for this office furnishing system to be connected to more than one source of supply. Disconnect all sources prior to any servicing. A single circuit shall not be powered by more than one source. WARNING - Electrical connection between rail segments shall be disconnected prior to removal of a mechanical connection.
- Page 3 Rail Segment Power Harness Power Harness Housing Cable Basket *Optional Spline Rod Floor Anchor for Stand- Alone Rail Segments Gallery End Panel Power Infeed Gallery End Panel Joiner Panel Gallery End Panel Rail Mount 3 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 4 2mm Hex Drill/ 3mm Hex Drill/ Driver Bit Driver Bit Additional tools such as a 90 Degree Bit and an 18” Extension are helpful for some steps *No torque or ball bits should be used 4 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 5 Start with the first rail of the run, and slide the end leg internal to the rail. Drive three screws from the bottom and one on each side. Screw M6-1.00 x 12MM BHSCS, Black (125285) 5 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 6 (2) screws per side. Repeat this step for all middle rail segments, adding two caps to each mid-segment rail, and one end cap to each end-segment rail. Screw Thread-Cutting M4 x 8MM FH PH, Zinc (0003016) 6 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 7 The bottom plate of the leg sits internal to the bottom plate of the rail. Screw M6-1.00 x 12MM BHSCS, Black (125285) 7 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 8 (0002086) Two-Piece Panels: Join Panels Together In the case of a two-piece Gallery End Panel, slide the spline rod into one screen, and then push the second screen onto the rod to secure together. 8 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 9 Screw the rail mount to the joiner panel using (4) screws, the top of the rail mount should come to a height of 27”. Screw SMS #10 x 3/4 Truss Head PH, Black (122875) 9 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 10 Screw in (2) thread cutting screws from each side of the rail bracket to secure the rail in place. Screw M6-1.00 x 12MM BHSCS, Black (125285) Screw Thread-Cutting M4 x 8MM FH PH, Zinc (0003016) 10 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 11 Ensure the jumper plastic clips are engaging the harness lip to prevent disconnection. The mid leg must be straight at the time of routing the jumper through. 11 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 12 (b.). Next secure the Steel (121538) infeed with the strain relief bracket where the infeed exits the rail (c.). 8-32x1/4” Screw, Steel (121538) 18-8 Lock Washer #8 .34” OD (121406) 12 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 13 Optional Cable Basket Attach Rail Mounts Attach mounting brackets to the rail mount plates on the the bottom rail rung with (2) button head screws per bracket (4 total). M6 - 1.00 X 12MM BHSCS (125290) 13 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 14 Secure Cable Basket Position the Cable Basket onto the mounting brackets and attach with (2) button head screws per bracket (4 total). M6 - 1.00 X 12MM BHSCS (125290) 14 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 15 The mid legs can bend to 90 degrees in either direction. The mid leg feet will pivot as the rail segments bend and should always remain perpendicular to the mid leg assembly. 15 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
- Page 16 In the case of a stand alone rail segment, the rail assembly must be mounted to the floor using the supplied floor anchor bracket and (4) floor anchor screws. Repeat with other End-Leg. Floor Anchor Screw (48013) 16 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...
-
Page 17: Wiring Schematic
WARNING: Risk of fire or electric shock. This of fice furnishing system may be connected to more than one source of supply. All sources must be disconnected prior to any ser vicing. No single circuit may be powered by more than one source. 17 EDISON JUNIOR RAIL ASSEMBLY INSTRUCTIONS...