Advertisement
Quick Links
Advertisement
Related Manuals for WATSON Tonic Worktable
Summary of Contents for WATSON Tonic Worktable
- Page 1 ASSEMBLY Tonic Worktable V.23.1 10/2023 360.394.1300 watsonfurniture.com...
-
Page 2: Important Safety Instructions
This product is for use on a nominal 120-V circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. 2 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS... - Page 3 8-32 X 1/4” THREAD CUTTING SCREW (121538) DATA MANAGER CLIPS (0000003) 8-32 WING NUT 8-32 X 1/4” SCREW 5/16-18 X 1.25” (888101) (121535) SCREW (125030) 5/16-18 X 3.5” SCREW (0002127) BLANK DATA PORT TIGHT JOINT (0001367) (0002294) 3 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 4 Tonic Worktable Components SPLICE PLATE CABLE SLAT INFEED JUMPER CABLE END COVER WORK SURFACE POWER BRICK TOP SUPPORT RAIL RACEWAY RAIL POWER RACEWAY END LEG ASSEMBLY PLANTER BOX FABRIC SCREEN 4 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 5 Electric Drill Driver Bit Driver Bit Driver Bit Driver Bit Additional tools such as a 90 Degree Bit and an 18” Extension are helpful for some steps *No torque or ball bits should be used 5 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 6 Top Support Rail Orient Leg Assemblies upright and attach top support rails with 4 screws (125285) per top support rail. M6 1.00 x 12mm Screw (125285) 6 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 7 Raceway Rail Attach raceway rails with 4 screws (125285) per rail. M6 1.00 x 12mm Screw (125285) 7 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 8 (a) Attach power bricks to power raceway using thread cutting screw (121538) with washer (121406). (b) Push data manager clips (0000003) into provided holes in top of power raceway. 8-32 X 1/4” LOCK WASHER THREAD CUTTING (121406) SCREW (121538) DATA MANAGER CLIPS (0000003) 8 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 9 (c) Create electrical connection between Power Bricks by connecting the Jumper Cables or Infeed to the end of power bricks. Check each connection by slowly pulling on each cable after making a connection. 8-32 X 1/4” SCREW (121535) 9 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 10 Ground Jumper Cables Ground the jumper cable to the power raceway with the provided screws (121538) and washers (121406). 8-32 X 1/4” LOCK WASHER THREAD CUTTING (121406) SCREW (121538) 10 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 11 (b) For two piece tops, tighten tite joints with T25 Torx bit. Completely secure splice plates to surfaces with 6 screws (0002147) per spice plate. After this step is completed, accessories may be attached. #10 X 1” WOOD SCREW (0002147) 11 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 12 Attach Planter (Optional) Secure planter box to work surface with 2 screws (0002127). 5/16-18 X 3.5” SCREW (0002127) 12 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 13 Attach Screen (Optional) Secure screen to work surface with 2 screws (125030) per screen. 5/16-18 X 1.25” SCREW (125030) 13 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 14 Attach Surface Use screws (0002147) to secure the work surfaces to the legs. #10 X 1” WOOD SCREW (0002147) 14 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...
- Page 15 Cable Slats Cable Slats go underneath the Power Raceway to keep data cables from hanging below the raceway. To install, rotate in between raceway rails until the fit is snug and secure. 15 TONIC WORKTABLE ASSEMBLY INSTRUCTIONS...