Advertisement
Quick Links
Advertisement
Related Manuals for WATSON C9
Summary of Contents for WATSON C9
- Page 1 ASSEMBLY C9 Meeting Tables + Accessories 360.394.1300 watsonfurniture.com V.1.00 08/2020...
- Page 2 Surface(s) Long Frame Rails Short Frame Rails Legs T-Legs* Support Rail Brackets* Support Rails* Double Flip Power Cable Tray Unit (Optional) (Optional) *Included only wit h cer t ain t able sizes 2 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 3 Hardware Rail Nut (0001120) #10 x 1/2” Philips M6-1.0x12mm Low T humbscrew (0000638) Top Clip (0001156) Screw (122815) Pr of ile Cap Screw (0001140) Tools Elec t r ic Dr ill Phillips Dr ill/Dr iver Bit 3mm Hex Dr ill/Dr iver Addit ional tools such as a 90 Degree Bit and an 18”...
- Page 4 Attach T-Legs to Frame Rails (for Multi- Piece Tables Only) (A) Insert the legs into the short frame rail and (B) secure using 8 screws (0001140). Repeat this step for the other side. 4 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 5 Attach Leg Assemblies to Long Frame Rails M6-1.0x12mm Low Prof ile Cap Screw (0001140) 5 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 6 Hang the Cable Tray(s) by inserting the tabs into the slots in the opposite support rail. Swing the tray(s) up into place and move sideways until the thumbscrews are fully seated in the tray’s keyslots. Tighten the thumbscrews. T humbscrew (0000638) 6 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 7 Attach a screw (0001140) through the top clip into the worksurface. Repeat for all clips. M6-1.0x12mm Low Top Clip (0001156) Prof ile Cap Screw (0001140) 7 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 8 Raise the power unit up to the worksurface dado and drive 6 screws (122815) to secure the unit in place. If applicable, connect an HDMI or CAT6 data cable to the female/female adapters provided. #10 x 1/2” Philips Screw (122815) 8 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 9 “cable area”. Firmly press the cable Cable Area channel onto the table leg. Note : Wat son Cable Tower as sembly inst r uc t ions are in a separ ate document Clamping Area 9 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 10 Monitor Mount Mid Mount Tray Cross Bars Hardware M6-1.0 X 8MM Low Har dware K it Envelope M6-1.0x12mm Low Rail Nut (0001120) Prof ile Cap Screw (0000909) Prof ile Cap Screw (0001259) (0001140) 10 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 11 Rail Nut (0001120) Attach Monitor Mount to Table Align the Monitor Mount the with the holes in the rail nuts and attach with (4) screws (0001140). M6-1.0 x 12mm Low Prof ile Cap Screw (0001140) 11 C9 ONE-PIECE MEETING TABLE ASSEMBLY INSTRUCTIONS...
- Page 12 M6 screws in the holes shown below. Note : t he ideal Monitor placement is 50mm gap fr om t able sur face to bot tom of Monitor. M6-1.0 x 12mm Low Pr of ile Cap Screw (0001140) 12 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
- Page 13 M6-1.0 X 8MM Low Prof ile Cap Screw (0001259) Install Alligator Clip Using (1) 0001259 M6 x 8mm screw install Alligator Clip at the bottom of the Monitor Mount M6-1.0 X 8MM Low Prof ile Cap Screw (0001259) 13 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...
-
Page 14: Additional Wiring
After the TV is mounted additional wiring can be routed into the Monitor Mount by pivoting the TV out. Push the bottom of the TV to rotate and route cables thru the Monitor Mount. 14 C9 MEETING TABLE & ACCESSORIES ASSEMBLY INSTRUCTIONS...