Javad Beacon User Manual

Oem receiver

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Beacon

OEM Receiver

User Manual

Version 1.0

Last Revised April 13, 2021

All contents in this manual are copyrighted by JAVAD GNSS.

stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express

written consent from JAVAD GNSS.

Table of Contents

Need help?

Do you have a question about the Beacon and is the answer not in the manual?

Questions and answers

Summary of Contents for Javad Beacon

Page 1 Version 1.0 Last Revised April 13, 2021 All contents in this manual are copyrighted by JAVAD GNSS. All rights reserved. The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express...
Page 3: Table Of Contents
Table of Contents Table of Contents Terms and Conditions ........5 Beacon Receiver Specification ....9 WEEE Directive ...........6 How to install Beacon OEM Receiver ..10 Screen Captures .........6 Dimensions ..........10 Technical Assistance ........6 16-Lead Header Connector Pinout ....11 Media Access Control (MAC) .......7 COMMAND LINE INTERFACE .......12...
Page 4 ALARM ............15 BOOT ............15 HELP ............15 SAVE ............15 SLEEP ............15 Diagnostics and Identification Commands ..........16 INFO ............16 STATE ............16 General Warnings ........17 www.javad.com...
Page 5: Terms And Conditions
JAVAD GNSS, Inc. (“JAVAD GNSS”) for owners of JAVAD GNSS products. It is designed to assist owners with the use of Beacon OEM Receiver and its use is subject to these terms and conditions (the “Terms and Conditions”).
Page 6: Weee Directive
Software and manual upon termination of your use of Beacon OEM Receiver. All ownership, copy- right and other intellectual property rights in and to the Software belong to JAVAD GNSS. If these license terms are not acceptable, return any unused software and manual.
Page 7: Media Access Control (Mac)
Description and Operation INTRODUCTION Marine Radiobeacon receiver (283.5 to 325 kHz) or Beacon receiver complies with Broadcast Standard for the USCG DGPS Navigation Service COMDTINST M16577.1. Beacon receiver is designed to receive pseudorange corrections transmitting by Radiobeacon stations. Maritime Radiobeacon DGNSS systems according to RTCM SC-104 version 2.3 are usually capable of broadcasting the following RTCM messages: 1, 2, 3, 5, 6, 7, 9, 15 (sel-...
Page 8: Serial Data Interface
The power interface allows connection to an unregulated DC power source. The DC power source (third party or user supplied) must provide DC power of 4.2V±5% DC. Power Consumption Power consumption of the Beacon OEM receiver at receiving mode is 1400 mW (refer to Table below for details). Operating Mode / Description...
Page 9: Technical Specification
• Up to 115200 bps Serial Interface • Data Rate • CompactDesign EXTERNAL CONNECTORS • J300 Beacon/GNSS RF Input Connector MMCX RIGHT ANGLE PCB JACK, AMPHENOL P/N 908-24100. • Through the central pin of the connector J300 the power is being supplied to the antenna LNA.
Page 10: How To Install Beacon Oem Receiver
Dimensions 2.933in 74.5mm pin 15 pin 1 3.159in 80.2mm Connectors, RF MMCX, Jack R/A PCB Mount, .068 LEGS Connector, 16-lead, Thru-hole 2x8, Header, ".050 HOW TO INSTALL BEACON OEM RECEIVER www.javad.com...
Page 11: 16-Lead Header Connector Pinout
TTL Input line An internal 100K pull-up resistor is applied. VCC42 External Power Supply Regulated positive 4.2V DC from ext. Power Supply. VCC42 External Power Supply Regulated positive 4.2V DC from ext. Power Supply. Connector, 16-lead, Thru-hole 2x8, Header, ".050 www.javad.com...
Page 12: Command Line Interface
• Saving into the configuration files the configuration parameters modified through the CLI. Command Line Interface Convention The following convention is implemented in Beacon Receiver Command Line Interface (CLI): • The Carriage Return/Line Feed (CR/LF, 0x0D/0x0A) is a command delimiter.
Page 13: Software Switching To Maintenance Mode
20 ms toggling on CTS control line followed by Escape-Acknowledge response is needed to acknowledge switching from Data to Maintenance mode and vice versa. In Maintenance Mode, the unit’s serial port must keep Clear to Send (CTS) line always active. Note: The powered up radio modem always goes to data mode. www.javad.com...
Page 14: Switching To Data Mode
RSSI and Reference station ID. The RSSI parameter ble to select the Frequency scanning and Signal type is recorded to determine the station providing the scanning criteria. best RTCM signal. If no Beacon reference station is SCAN [Parameter Name] [Parameters List] www.javad.com...
Page 15: Antenna
283.5 kHz to 325 kHz) and signal type (200 ware/Software Versions bps, 100 bps or 50 bps) for Master Beacon to tune. The MAP - Operate with Channel Map Slave Beacon performs Full range scanning for all sig- ANTENNA - Set the State of antenna power nal types and fills the Almanac table in parallel.
Page 16: Diagnostics And Identification Commands
The SLEEP command determines the sleep mode pa- Parameter Parameter List rameters. The sleeping Beacon OEM Receiver can Name be activated by real-time CLK, DTR/RTS lines, and Retrieves the version string of the BootLoader. command received through TTL inputs. The user can Ver.
Page 17: General Warnings
• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, shall be placed on the apparatus. www.javad.com...
Page 18 Warranty terms JAVAD GNSS Inc. (“Company”) warrants, to the PURPOSE, AND IF APPLICABLE, IMPLIED WARRANTIES end-user only, that the Narrow Band Radio Modems UNDER ARTICLE 35 OF THE UNITED NATIONS CON- (“Radios”) purchased (a) conforms to the Company’s VENTION ON CONTRACTS FOR THE INTERNATIONAL published specifications for the model purchased, SALE OF GOODS.

Javad Beacon User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Javad Beacon

Summary of Contents for Javad Beacon

Table of Contents