Page 1
VERSION 1.2 LAST REVISED MAY 26, 2019 All contents in this manual are copyrighted by JAVAD GNSS. All rights reserved.The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express...
TURNING ON/OFF ........12 MEASURE ANTENNA HEIGHT ....20 CHARGING THE BATTERIES ....12 COLLECTING DATA .........21 POWER SUPPLY REQUIREMENTS ..12 STATIC SURVEYING FOR BASE STATIONS . POWERING THE RECEIVER ....13 KINEMATIC (STOP & GO) SURVEYING FOR SIM CARD SLOT ........13 ROVER STATIONS ........21 www.javad.com...
Page 4
LOADING OAFS ........23 CLEARING THE NVRAM ......23 USING MINPAD TO CLEAR NVRAM ..24 USING NETVIEW TO CLEAR NVRAM ..24 CHECKING FIRMWARE VERSION ...24 LOADING NEW FIRMWARE .....24 TROUBLESHOOTING ......24 CHECK THIS FIRST! ........24 RECEIVER PROBLEMS ......24 TECHNICAL SUPPORT ......26 www.javad.com...
JAVAD GNSS products. It is designed to DISCLAIMER OF WARRANTY – EXCEPT FOR ANY assist owners with the use of TRIUMPH-1M and its use WARRANTIES IN THIS MANUAL OR A WARRANTY is subject to these terms and conditions (the “Terms CARD ACCOMPANYING THE PRODUCT, THIS MANUAL and Conditions”).
For more detailed information about the in and to the Software belong to JAVAD GNSS. If these take-back and recycling of this product, please con- license terms are not acceptable, return any unused tact your supplier where you purchased the product software and manual.
G – gain of the antenna in the direction of interest relative to an isotropic radiator (numeric), d – distance to the center of radiation of the antenna (in cm). Regarding the Javad TRIUMPH-1M device contain- ing multiple transmitters: • UHF module (FCC ID: WJ4LMR400), •...
Page 8
RF exposure compliance is performed: Note: N7NMC7700 can transmit only in any one of four modes in time of operation. The worst case is transmitting in Cell band. www.javad.com...
INTRODUCTION pseudoranges) between it and at least four satellites. The measured pseudoranges are corrected for clock The new TRIUMPH-1M receiver inherits the best differences (receiver and satellites) and signal prop- features of our famous TRIUMPH-1. Based on our agation delays due to atmospheric effects. The posi-...
MicroSIM card slot User accessible, fully sealed Radio Modem Internal 406-470MHz UHF radio Internal 902-928/ 868-870 MHz ISM radio (optional) Base Power Output 1 Watt Memory and Recording Internal Memory Up to 16 GB of on-board non-removable memory for data storage www.javad.com...
GETTING ACQUAINTED The TRIUMPH-1M receiver’s advanced design re- duces the number of cable required for operation, allowing you to survey more reliably and efficient- ly. The casing allocates space for two rechargeable batteries, SIM card and SD card slots, a Bluetooth®...
• Yellow – less than 10 min memory left. ment and shall be easily accessible. • Red – memory is full. A single external power supply with 5 pin ODU • No light - not active. connector or SAE connector is necessary to operate www.javad.com...
To check the status of the internal batteries, view connector, Receiver-to-SAE power cable shall be the BAT LED or check the status using JAVAD GNSS used. The external power supply needs to be Listed software. Check the BAT LED for battery status.
RECEIVER USING NETVIEW MOUNTING This software is available on the JAVAD GNSS web- site. If downloading the program(s) from the website, extract the program’s files into a folder on your hard The bottom connector connects the receiver to ei- drive.
NetView Establishing an USB connection Both Base and Rover receivers must be configured Make sure the computer has JAVAD GNSS’s USB according to the desired survey method. driver installed (available from www.javad.com) be- • In applications where real-time positioning re- fore continuing.
Page 16
This data is then processed using post-processing software (for example, Justin). The following Base and Rover configurations are recommended for the most common applications. However, you can select configuration parameters as needed for your particular jobsite. www.javad.com...
Page 17
• Confidence Level for Ambiguity – list box governs the process of the RTK engine fixing integer ambi- guities. The RTK engine uses the ambiguity fix indi- cator when making a decision whether to fix ambi- guities or not. Low, Medium and High correspond www.javad.com...
Note: For detailed description of settings and parameters see parameters.. NetView Software Manual.. MINPAD CONFIGURATION The TRIUMPH-1M’s simple user interface (MinPad) consists of two keys (Power and Record) and up to six LEDs that control and display the receiver’s operation (see Figure 3 on page 12).
20 characters long. Default is log. • Enable Implicit Management of Specific - en- ables/disables the management of Implicit Mes- sage Output Period. Figure 17. AFRM • Period – specifies the time duration of each of www.javad.com...
• Method of measuring the antenna height • Model of the antenna used Record the antenna height, point name, and start Antennas have two types of measurements: www.javad.com...
Figure 18. Установка TRIUMPH-1M following factors: To start survey TRIUMPH-1M should be set up on a • The length of the baseline measured tripod or in a pole. TRIUMPH-1M has 5/8” mount to • The number of satellites in view connect to monopod, to tripod or to surveying pole.
Usually, the receiver will start to output the coor- receiver requires firmware to properly operate and dinates of the antenna’s phase center along with the provide appropriate functionality. As JAVAD GNSS re- solution type within 10–30 seconds. However, UHF ra- leases firmware updates, loading these updates into...
You should download files as soon as Loading OAFs possible after collecting data at the jobsite. NetView JAVAD GNSS dealers provide customers with OAF provides a File Manager to download files to your files. For any OAF related questions, E-mail at sup- computer and delete files from the receiver DELTA.
Confirm NVRAM clearing. Check that the most current software is down- loaded onto the computer and that the most current CHECKING FIRMWARE firmware is loaded into the receiver. Check the JAVAD VERSION GNSS website for the latest updates. Then, try the following:...
Page 25
The receiver port used for connection is not in to enable or extend validity of the corresponding re- Command mode. ceiver options. Contact your dealer or visit the JAVAD Connect your receiver and a computer using a free GNSS website for details.
“Check This First!” for some solutions that may fix the issue. To contact JAVAD GNSS Customer Support use the QUESTIONS button available on the www.javad.com. For quick and effective support, provide a detailed description of the problem.