Download
Share
Print this page
Javad SIGMA Configuration Example
  1. Manuals
  2. Brands
  3. Javad Manuals
  4. Receiver
  5. SIGMA
  6. Configuration example

Javad SIGMA Configuration Example

As rover with hpt404bt connected through bluetooth
Hide thumbs Also See for SIGMA:

Advertisement

Quick Links

Download this manual
SIGMA as Rover
with HPT404BT connected through Bluetooth
Configuration Example
Version 1.0
Last Revised: December 21, 2011
All contents in this manual are copyrighted by JAVAD GNSS.
All rights reserved.The information contained herein may not be used, accessed, copied,
stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express written
consent from JAVAD GNSS

Advertisement

loading

Related Manuals for Javad SIGMA

Summary of Contents for Javad SIGMA

  • Page 1 Version 1.0 Last Revised: December 21, 2011 All contents in this manual are copyrighted by JAVAD GNSS. All rights reserved.The information contained herein may not be used, accessed, copied, stored, displayed, sold, modified, published, or distributed, or otherwise reproduced without express written...
  • Page 2 www.javad.com...
  • Page 3 2. Attach the Bluetooth antenna to Bluetooth antenna connector. 3. Connect the receiver to PC using serial (RS232) or USB port. If the USB connection will be used, ensure the special USB driver is downloaded from JAVAD GNSS’s website and installed (http:// javad.com/downloads/javadgnss/drivers/usb/jgnss_usbio.zip) 4.
  • Page 4 Sigma as Rover Sigma Configuration 7. Check the satellites are tracked. Click on the receiver’s name on the left. On the right the informa- tion about tracked satellites will be displayed: Figure 2. Satellites 8. Click GREIS Commands tab on the left and then click Capture on the right (Figure 3 on page 5).
  • Page 5 Sigma as Rover Sigma Configuration 9. Enter the command print,blt:on and click Send. Than copy or enter the SIGMA Bluetooth Mac Address, i.e. the value of the parameter addr= Figure 3. GREIS Commands 1 10. Enter the command %%set,dev/ser/e/imode,rtcm3 and click Send.
  • Page 6 Sigma as Rover Sigma Configuration 11. After the receivers reply RE002% click the Release button (Figure 4). Figure 4. GREIS Commands 2 www.javad.com...
  • Page 7 Sigma as Rover Sigma Configuration 12. Click Parameters on the left and then select pd for Position Computation Mode and click Apply: Figure 5. NetView. Positioning tab Now HPT404BT should be configured. Do not turn off the SIGMA receiver. www.javad.com...
  • Page 8 1. Attach the UHF antenna to BNC antenna connector. 2. Connect the modem to PC using serial (RS232) or USB port. If the USB connection will be used, ensure the special USB driver is downloaded from JAVAD GNSS’s website and installed (http:// javad.com/downloads/javadgnss/drivers/usb/jgnss_usbser.zip).
  • Page 9 9. In the BT tab set the BT to off and click Apply: Figure 7. BT tab 10. Enter the SIGMA’s MAC Address to the Destination Address field; Set Mode to Master, and then BT to ON. Figure 8. Settings for BT tab 11.
  • Page 10 Sigma as Rover HPT404BT Configuration Connect to the SIGMA via NetView. If all parameters were set correctly, SIGMA will receive the fixed solution: Figure 9. NetView www.javad.com...
  • Page 11 Sigma as Rover HPT404BT Configuration www.javad.com...
  • Page 12 900 Rock Avenue, San Jose, CA 95131 USA Phone: +1(408)770-1770 Fax: +1(408)770-1799 www.javad.com Copyright © JAVAD GNSS, Inc., 2011 All rights reserved. No unauthorized duplication.