Advertisement
Quick Links
A S S E M B LY I N S T R U C T I O N S
Birkdale Vinyl Fence Kit
(48 1/2"H x 92"W)
Please read through before starting assembly.
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 877 234 6196 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Post Caps (2)
2. Top & Bottom Rails (2) - 1½" x 1½" x 92"
3. Posts (2) - 7/8" x 1½" x 71"
4. Spindles (15) ¼" x 1½" x 46 ¼"
5. Joiner Clips (2)
6. 3/4" Self-Auguring Stainless Steel Screw (12)
Tools You Will Need
• Cordless Drill
• Level
• Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e. shipping box) to avoid scratching.
• We recommend an area approx 5'x 8' for unobstructed assembling.
• You should not need to use excessive force when assembling components.
45 in
48 1/2 in
20 in
1
2
3
4
5
6
Not to Scale
THIS FENCE IS DESIGNED
FOR SEMI-PERMANENT
APPLICATIONS
92 in
3 7/8 in
2 in
41 3/4 in
43 9/32 in
51 1/2 in
Ground
1
Ver 1.1/060317
Advertisement
Related Manuals for Zippity Birkdale
Summary of Contents for Zippity Birkdale
- Page 1 A S S E M B LY I N S T R U C T I O N S Birkdale Vinyl Fence Kit (48 1/2”H x 92”W) THIS FENCE IS DESIGNED FOR SEMI-PERMANENT APPLICATIONS 92 in 3 7/8 in 45 in...
- Page 2 S T E P O N E Position the bottom rail with routed holes for spindles facing upwards. 2 & 3 Slide one post down thru the routed hole in the bottom rail (that has the pre-drilled hole) until the pre-drilled hole in post and rail align.
- Page 3 S T E P T W O Insert the spindles into the routed holes as illustrated. Note: the tabs on the bottom of the spindles are intended to go into the bottom rail to lock spindles into place. Push the top rail down over the posts and spindles as illustrated. Note: Once inserted, the spindles will lock into place.
- Page 4 S T E P T W O Secure the rails to the post with screws on both sides of the top rail as illustrated. B i r k d a l e Vi n y l F e n c e I n s t r u c t i o n s...
- Page 5 S T E P T H R E E Install fence into Ground Move the fence to its final location and identify the location of posts. Loosen the top 10” to 12” of the ground using a claw hammer and screw driver (or something equivalent) as illustrated. Add water to loosen soil.
- Page 6 S T E P T H R E E OPTIONS IN HARD GROUND If your ground is too hard, or you have more than 3 or 4 panels to install, please consider: Purchase a 1 3/4” diameter auger bit (commonly used for planting tulips) as illustrated ($15-$20 on Amazon.com) Drill a hole in the ground at the desired location only about 8”...
- Page 7 S T E P T H R E E Install fence into Ground - Continued Level the assembled unit and backfill and compact dirt around the base of each post to strengthen the unit. Finish the assembly by pushing the post caps down over the Level top of posts as illustrated.
- Page 8 Screws are self-drilling. Fasten the opposite end of the joiner clip as illustrated. 10616 Bailey Road, Unit H, Cornelius NC 28031 www.zippity-outdoor.com Toll Free Phone: 1 877 234 6196 Fax: 704 631 4685...